Bedienungsanleitung Samsung SWV-800F (Seite 6 von 25) (Englisch)

34867

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

Installing the Washing Machine

SAMSUNG Washing Machine Owner’s Instructions

Connecting the water supply hose

The water supply hose must be connected to the washing machine at one end and to the water faucet at

the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the

water faucet, replace the hose with a longer, high pressure hose.

To connect the water supply hose:

1. Connect the cold water supply hose(Blue) fitting with the L-shaped arm to the cold water supply

intake(Blue) on the back of the washing machine and hand tighten.

2. Connect the other end of the cold water supply hose to your sink’s cold water faucet and tighten it

by hand. If necessary, you can reposition the water supply hose at the washing machine end by

loosening the fitting, rotating the hose, and retightening the fitting.

Option :

1. Connect the hot water supply hose(Red) fitting with the L-shaped arm to the hot water supply

intake(Red) on the back of the washing machine and hand tighten.

2. Connect the other end of the hot water supply hose to your sink’s hot water faucet and tighten it by hand.

3. If you want to use only cold water, use Y-piece.

Positioning the drain hose

The end of the drain hose may be positioned in three ways:

Over the edge of a sink

The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent,

use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece

of string to prevent the drain hose from moving.

In a sink drain pipe branch

The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60

cm above the ground.

90 cm

60 cm

1.Remove the adaptor

from the water

supply hose.

2.First,using a "+" type screw driver,

loosen the four screws on the

adaptor. Next,take the adaptor and

turn part(b) following the arrow for

gap about 5mm between them.

3. Connect adaptor to the water tap by

tightening the screws firmly.

Then,turn part (b) following the

arrow and put (a) and (b)together.

5. Connect the other end of the water supply

hose to the inlet water valve at the top of

the washer. Screw the hose clockwise all

the way in.

● If the water tap is a screw type,assemble a

water supply hose that fits to the tap as

shown.

4. Connect the water supply hose to the

adaptor. Pull down the part (c) of the water

supply hose. When you release part (c) the

hose is automatically connects to the

adaptor making a 'click' sound.

NOTICE

After completing connection,if water leaks from the hose,then repeat the same steps. Use the most conventional type of faucet

for water supply. In case the faucet is square or too big,remove the spacing ring before inserting the faucet into the adaptor.

Connecting the water supply hose (Option)

SWV1200F-00163A-dw 9/9/02 11:37 AM Page 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung SWV-800F Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info