Bedienungsanleitung Samsung WA95G9 (Seite 10 von 16) (Englisch)

577229

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

10_Installation & maintenance

installation & maintenance

The User’s Manual is for common use. Make use of the User’s Manual depending upon your washing machine model.

ENVIRONMENT

Leave some space - Maintain at least 10cm between the washer and the wall.

Place the washer on a sturdy flat surface. - If the washer is placed on an uneven or weak surface, noise or

vibration occurs. (Allowable is 1˚) Adjust the legs for even placement.

Never install the washer near water. - Do not place the washer in steamy rooms or where the washer is directly exposed to rain.

Moisture may destroy the electrical insulation causing an electrical shock hazard.

Avoid direct sunlight or heaters. - As plastic an electrical components are affected by direct heat, never place the

washer near furnaces, boilers, etc. Do not place under direct sunlight.

LEVELLING

If the washer is not leveled with the ground, it makes the machine tremble more or be out of order.

So, make sure that the washer is leveled properly.

SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF

THE WASHING TUB.

• Open the lid of the machine, pour water into the tub up to the level just

below the pulsator, and adjust the legs so that the pulsator is positioned

at the center of the water as shown in the figure.

• Place the machine more than 10cm away from the wall.

• Adjust the legs on feet for levelling.

CONNECTING THE WATER SUPPLY HOSE

1. Remove the adaptor from the

water supply hose.

Connect the water supply hose to

the adaptor. Pull down the part (c)

of the water supply hose. When

the part (c) is released, the hose

is automatically connected to the

adaptor making a ‘click’ sound.

2. First, using a “+” type screw driver,

loosen the four screws on the

adaptor. Next, take the adaptor

and turn part(b) following the arrow

for gap about 5 mm between

them.

5. Connect the other end of the

water supply hose to the inlet

water valve at the back of

the washer. Screw the hose

clockwise all the way in.

3. Connect adaptor to the water

tap by tightening the screws

firmly. Then, turn part(b) following

the arrow and put (a) and (b)

together.

5-1. Connect the other end of

the water supply hose to the

inlet water valve at the top of

the washer. Screw the hose

clockwise all the way in.

•

If the water tap is a screw type, assemble a water supply hose that fits to the tap as shown.

After completing connection, if water leaks from the hose, then repeat the same steps.

After completing connection, if water leaks from the hose, then repeat the same steps. Use the most

conventional type of faucet for water supply.In case the faucet is square or too big, remove the spacing ring

before inserting the faucet into the adaptor.

Water

LOOSEN LOCK

WA85G5P-02898D-02_EN.indd 10 2011-08-23 �� 12:21:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samsung WA95G9 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info