Bedienungsanleitung Sangean WFR-70 (Seite 12 von 84) (Englisch)

667073

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

3. The manually specified IP address should be chosen to be compatible with the settings in

your router and must be a unique address on your network. If you are using DHCP for some

devices and static (manually congured) IP addresses for others, the IP address used should

fall outside the range that the router may allocate using DHCP. Typically, the rst three groups

of digits will be the same for all devices on your network. To enter the IP address, rotate the

Tuning Control Rotary to set the value for each group of digits and then press the Tuning

Control Rotary to enter the value and to move on to the next group. When the IP address has

been entered, the subnet mask should be entered. The subnet mask denes which parts of

the IP address are common across your network. For most small networks the subnet mask

will be 255.255.255.0 and this is entered in the same way.

4. The Gateway address is normally the IP address of the router through which the radio

connects to the internet and is entered in the same way as the previous addresses.

5. In most installations the DNS settings (DNS = Domain Name Server) will be set to the same IP

address as your router. In this case the secondary DNS may be left at zero. To enter the DNS

address, rotate the Tuning Control Rotary to set the value for each group of digits and then

press the Tuning Control Rotary to enter the value and to move on to the next group. Repeat

this until all eight groups of digits have been entered.

6. The next step is to set up the WiFi connection, starting with the name of the wireless network

(SSID) followed by the encryption options and password. To enter the SSID, characters are

selected and entered using the Tuning Control Rotary The radio scrolls through the available

characters as well as the three controls on the right. The character currently highlighted will

be entered when you press the Tuning Control Rotary. Do this as needed until the complete

network name has been entered. The SSID setting is sensitive to upper and lower case

characters and symbols.

You must enter it exactly as set up in your router. The three controls on the right-hand side of

the screen have special functions:

select ‘ ’ to erase a character just entered

select ‘ ’ when the complete SSID has been entered

select ‘ ’ to cancel and go back to the DNS settings screen

7. Having entered the SSID, you must enter details of the encryption system used on your

wireless network. This should be the same as specied in your router settings. If your network

does not use encryption, then select the ‘Open’ option. Your radio should then connect to

the network, so skip to step 11. If your network uses WEP (Wired Equivalent Privacy) select

the‘Pre-Shared Key’ option then go to step 8. The remaining options are for WPA or WPA2 (WiFi

Protected Access) – see step 9.

Primary DNS

Secondary DNS

192

DNS

5/9

168 1 1

0 0 0

SSID

6/9

7/9

Open

Pre-Shared Key

WPA

WPA2

Authentication

8/9

Disabled

WEP

Encryption type

9/9Key:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean WFR-70 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sangean WFR-70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info