Bedienungsanleitung Sangean WR-50 (Seite 6 von 21) (Englisch)

797031

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Using the radio for the

rst time

1. Place your radio on a

at surface.

2. Insert the adaptor plug into the DC socket located on the rear of

your radio. Plug the adaptor into a standard AC outlet. If no time is

displayed, the screen will show “--:- - -- ”.

3. Fully extend the FM telescopic antenna located on the rear of your

radio.

4. Press and release the Standby button to turn on your radio. It may

be necessary to relocate your radio to a position giving better

reception and carry out a scan to

nd stations as described in

later sections.

IMPORTANT:

The AC adaptor is used as the means of connecting the radio to

your power supply. The AC Adapter used for the radio must remain

accessible during normal use. In order to disconnect the radio from

the power completely. The AC Adapter should be removed from the

main power completely in case of severe lightning or storm.

Antenna setup for AM reception

The radio comes with a built-in AM Ferrite antenna which should be

enough for normal listening.

To improve the AM reception, first try to rotate the unit 90 degrees,

if this doesn't help you may connect an external AM antenna (not

supplied) to the AM external antenna terminal on the back of your radio.

Operating your radio – FM/AM auto-tune

1. Fully extend the FM telescopic antenna located on the rear of your

radio.

2. Press and release the Standby button to switch on your radio.

3. Press the Source button repeatedly to select the desired frequency

band.

4. If this is the first time searching for an FM/AM station, press and

release the Tuning control knob, the radio will search from low

frequency to high frequency and stop automatically when it

nds a

station of suf

cient strength.

5. For scanning stations backwards quickly, rotate the Tuning control

knob in an anticlockwise direction rst, and then press and release

it. Your radio will scan down the FM/AM frequency band from the

currently displayed frequency and will stop scanning when it finds

a signal of sufficient strength. To scan up in frequency, rotate the

Tuning control knob in a clockwise direction. The displayed frequency

will increase. Then press and release the Tuning control knob to

carry out auto-tune. Your radio will scan up the FM/AM frequency

band from the currently displayed frequency and will stop scanning

when it nds a station of sufcient strength.

6. After a few seconds the display will update. The display will show the

frequency of the signal found. If the signal is strong enough and there

is RBDS data present then the radio may display the station name.

7. To

nd other stations press the Tuning control knob as before.

When the end of the frequency band is reached, your radio will

recommence tuning from the opposite end of the frequency band.

8. Adjust the Volume to the required setting.

9. To switch off your radio, press and release the Standby button. The

display will show the “OFF” symbol.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean WR-50 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info