Bedienungsanleitung Sanibroyeur SANICOMPACT 48 ECO Plus (Seite 8 von 40) (Alle Sprachen)

532726

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

DESCRIPTION

SANICOMPACT

Eco is a WC specially designed with

an integral pump/macerator. SANICOMPACT

Eco is for

domestic use.

Installed and used correctly, SANICOMPACT

Eco will give

consistent and reliable service.

Please note the following warning signs:

» Possible danger to personnel,

» Warning of possible electrical hazard.

«WARNING» This is a general warning that failure to

follow instructions could result in poor functioning

of the unit.

OPERATING PRINCIPLE

SANICOMPACT

Eco is controlled by an electronic

programmer.

It has a macerating and pumping function. To start press

one of the two grey sides (light grey: small flush, dark grey:

large flush) of the button integrated to the bowl.

LIST OF ACCESSORIES INCLUDED

DIMENSIONS

TECHNICAL DATA

Applications discharge of a WC

Type

CR15 DF

Maximum Vertical Pumping 3 m

Voltage 220-240 V

Frequency 50 Hz

Normal Power Rating 550 W

Maximum current consumption 2,5 A

Electric Class I

Degree of protection IP44

Maximum water temperature 35°C

Net Weight C3 28,6 Kg

C5 29,0 Kg

C6 26,5 Kg

C43 23,2 Kg

C48 25,4 Kg

WARNING: Only installations conforming to the above

specifications are acceptable.

PERFORMANCE CURVE

INSTALLATION

ATTACHING THE TOILET TO THE FLOOR

Place the SANICOMPACT

Eco in the desired location.

Trace round the position of the bowl and mark the postition

of the fixing screws. Remove the bowl and then mark the

position of the fixing brackets 15mm inside the drawn line

(see dia

Remove the toilet bowl.

Drill through the flooring.

If necessary, and if you have time, lay a silicone joint

around the location of the toilet bowl.

Install the fixing screws and brackets. Put the

SANICOMPACT

Eco in place. Use the screws to fix the

SANICOMPACT

Eco to the floor.

CONNECTION OF THE DISCHARGE

1 - Fully insert the elbow

in the end of the rubber

waste tube, after turning it to face in the desired

direction.

2 - Fix the base of the elbow

and tighten it on the

rubber waste tube with a clamp

3 - Connect the sleeve

to the end of the elbow with

the clamp

. Cut off the end of the sleeve to adapt it to

the waste pipe. Connect the 32mm wastepipe into the

sleeve and secure with jubilee clip

4 - Warning: Ensure that you do not twist the discharge

pipework inside the unit.

5 - Warning: The horizontal portion of the discharge pipe

should be installed in a gravity flow, (1/4 inch to 1 foot).

Avoid any low parts in the discharge pipe.

6 - Warning: Protect pipes against freezing with appro-

priate insulation. If the toilet is installed in an unheated

location during freezing periods protect it as follows:

• Shut off the water supply,

• Activate one cycle without water,

• Pour antifreeze in the bowl (2 litres),

• Flush the toilet.

7 - Warning: Any bends in the discharge pipe run should

be smooth radius bends. If using plastic pipe two 45

degree offsets can be used to form a smooth bend.

8 - Note: We would recommend that a drain-off point is

installed to allow the discharge pipework to be drained

down before any service work.

9 - Note: To avoid siphoning, install a an anti-siphon valve

at the high point of the installation.

CONNECTION TO THE WATER SUPPLY

Connect the water supply hose to a shut off valve

Caution: The quality of the rinsing of the bowl depends on

the water pressure.

WARNING: for a correct rinsing, the water pressure should

be at least 25 PSI (1,7 bars).

Note: In an area where water is not pure (dirty, sandy), we

advise you to add a filter between the shut off valve and the

toilet to prevent clogging of the solenoid valve.

CONNECTION TO THE ELECTRICAL SUPPLY

The electrical installation should be carried by a

qualified person.

All wiring must conform to BS7671, 1992 requirements for

electrical installation. The unit requires a 220/240 V single

phase AC 50 Hz supply (UK specification). Do not connect

the unit to a conventional plug and socket. The unit should

be connected to a fully earthed electrical supply (class 1).

It must be wired into an unswitched fused fixed wiring

connector protected by a 5 amp fuse and a residual cur-

rent detector (30 mA). This connection must be used

exclusively for supplying the unit.

The wires in the mains lead are coloured in accordance

with the following code:

Brown – Live

Blue – Neutral

Green/Yellow – Earth

WARNING: Ensure the electricity is turned OFF at the main

switch board before wiring to connector. All work on cable,

pressure chamber and motor should only be carried out

by a qualified Saniflo servicing agent, as special tools are

required.

Fully illustrated step by step instructions are

downloadable on www.saniflo.co.uk

9008 SANICOMPACT ECO N°107.indd 8 14/06/10 12:30:20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanibroyeur SANICOMPACT 48 ECO Plus Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanibroyeur SANICOMPACT 48 ECO Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info