Bedienungsanleitung Sanibroyeur SANICONDENS Pro (Seite 8 von 32) (Alle Sprachen)

532746

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

CAUTION

SANICONDENS

Pro is a pump for lifting condensation

water from an air conditioning system, a condensation boiler

or from refrigeration units. Include a neutralisation device if

necessary (see the manufacturer’s instructions for your boiler).

The pump starts automatically and has a high level of

performance, safety and reliability provided that all the

installation and maintenance instructions described in this

notice are strictly followed.

Please take particular note of the information marked by :

» Indication that a risk of electrical origin exists,

« » Instructions for use only by qualified professionals.

OPERATING PRINCIPLE

SANICONDENS

Pro contains a pump. The tank of the

SANICONDENS

Pro is fitted with a float which controls the

operation of the motor. When the condensates enter the

tank, the pump starts up.

LIST OF DOCUMENTS PROVIDED:

see fig.2

DIMENSIONS:

see fig.3

SANICONDENS

Pro AREA OF APPLICATION AND

TECHNICAL DATA

Application

Air conditioning systems, boilers,

refrigeration units

Type CD10

Max. vertical pumping 4,5 m

Maximum flow rate (litres / hour) 342

Flow rate at 4 m 156

Min. pH 2,5

Voltage 220-240 V

Frequency 50 Hz

Power rating 60 W

Current consumption 0,52 A

Electrical class I

Protection index IP20

Sound level < 45 dBA

Average utilisation temperature 35°

Maximum allowable temperature 80°

S3 15% (90s ON, 510s OFF)

Net weight 2000 g

Tank volume 2 litre

Supply cable 2 m

Discharge hose 6 m

Alarm cable (3 core) 2 m

Wall fastening Yes

CAUTION:

All applications other than those described in this notice are

prohibited.

PERFORMANCE CURVES:

see fig.5

VERTICAL PUMPING/HORIZONTAL PUMPING:

see fig.6

INSTALLATION

SANICONDENS

Pro has wall fixings.

The unit should be easy to access for testing and

maintenance.

The unit must be installed level. Adjust the installation

using a spirit level before fixing the unit.

Make sure that the equipment is protected from damp while

installing it.

CONNECTION AT THE COVER INLET

The unit has 2 inlets 28 mm in diameter (1 on each side - see

fig.

). To connect the water to be drained off, connect the

water inlet to one of the inlets. If necessary, use the rubber

adaptator

19, 32, 40 mm.

CONNECTING TO THE DISCHARGE PIPE

The SANICONDENS

Pro discharge pipe must be connec-

ted to the flexible hose

(supplied : length 6 m). This hose

should be used to form the vertical section of the discharge

pipe.

• Place the flexible hose onto the non-return valve of the

SANICONDENS

Pro (see diagram

)

• Position the flexible hose in the most vertical position

possible to avoid it kinking.

• It is advisable to make a smooth bend to avoid the hose

kinking.

• The hose has a diameter of less than 8 mm and can be

connected to a PVC hose of larger diameter by a plastic

reducing connection on the horizontal section of the dis-

charge hose, or connected to your drain by a plastic redu-

cing connection

. In UK fittings such as Speedfit from

John Guest are available -part numbers PEM202215W

used with PEM06150W to connect to 22mm pipework.

The SANICONDENS

Pro is fitted with a non-return valve

to prevent re-activation.

ELECTRICAL CONNECTION

The electrical installation should be carried by a qualified person.

The unit should be connected to a fully earthed electrical

supply. All wiring must conform to BS7671, 1992 requirements

for electrical installations. The SANICONDENS

Pro requires a

220/240V single phase AC 50 Hz supply (UK specification). Do

not connect SANICONDENS

Pro to a conventional plug and

socket. It must be wired into a fused, unswitched, fixed wiring

connector fitted with a 5 amp fuse. SANICONDENS

Pro has

an Earth wire. The wires in the mains lead are coloured in accor-

dance with the following code:

Brown – Live Blue – Neutral Green/Yellow – Earth

Warning: Ensure the electricity is turned OFF at the main

switch board before wiring to connector.

All work on cable, pressure chamber and motor should only

be carried out by a qualified Saniflo servicing agent, as

special tools are required.

ALARM

SANICONDENS

Pro is fitted with a detection system

that can trigger an alarm if the water level rises too high

(audible or visual alarm, 1.5V to 230V), see diagram

. Brown wire: shared wire

. Black wire: normally off

. Blue wire: normally on

To fit the alarm, connect the blue and brown wires

of the alarm to the respective terminals on the

SANICONDENS

Pro.

INSTRUCTIONS INTENDED SOLELY FOR

QUALIFIED PROFESSIONALS

INSTRUCTIONS INTENDED SOLELY FOR

QUALIFIED PROFESSIONALS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanibroyeur SANICONDENS Pro Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info