Bedienungsanleitung Sanibroyeur SANICUBIC 2 Classic - 169 (Seite 17 von 78) (Alle Sprachen)

671245

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

DESCRIPTION

This pumping station is (manufactured in a factory

which is quality) certiﬁed to ISO 9001. Installed and

used correctly, the unit will give consistent and

reliable service.

This device is not designed for persons (in-

cluding children) with limited physical, sensory

or mental abilities, or those with minimal expe-

rience and knowledge, unless they are moni-

tored and are given the necessary instructions

for using the device, with the help of a person

responsible for their safety. Monitor children and

make sure they do not play with the device.

APPLICATIONS

SANICUBIC® 1 and SANICUBIC® 1 WP are pumping

stations specially developed for individual use (de-

tached house or small commercial premises).

SANICUBIC® 2 Classic and SANICUBIC® 2 Pro are

pumping stations specially developed for indivi-

dual, commercial and small community use (small

buildings, shops, public places).

SANICUBIC® 2 XL is a pumping station specially de-

signed for community use (professional buildings,

restaurants, industries, schools, hotels or shopping

centres).

These devices comply with the EN 12050-1 stan-

dard (pumping station for waste water contai-

ning faeces) as well as the European directives on

construction products, electrical safety and elec-

tromagnetic compatibility.

INSTALLATION

The SANICUBIC® must be installed in compliance

with standard EN12056-4. The equipment must be

commissioned and maintained by a qualiﬁed pro-

fessional specialist.

1- Attention: the space in which the SANICUBIC®

is to be installed must be large enough to leave at

least 600 mm of working room around and above

the unit to facilitate such maintenance work as may

be required.

There must be suﬃcient lighting, and it must be

suﬃciently well ventilated and protected from

freezing.

2-Isolating valves (not supplied) must be tted

on waste inlets (especially the 110mm inlets)

and on the discharge to ensure that any service/

maintenance may be carried out safely).

3- The discharge pipe must be ﬁtted so as to avoid

all back ﬂow from the drainage system (see the

examples in drawing). Back ﬂow can be avoided

by installing an anti-back ﬂow riser reaching a high

point above the maximum back ﬂow level.

Comment: In the absence of local information to

the contrary, the maximum back ﬂow level corres-

ponds to street level (roadway, pavements, etc.).

Continue the discharge pipework after the anti-

backﬂow riser, using a larger diameter pipe.

4- If the SANICUBIC® is installed in a space such as

a pit for example, we would recommend the ﬁtting

of a bilge pump in case of ﬂooding.

5- The lifting station must be vented with an open

vent outlet at roof level. Do not ﬁt an air admit-

tance vale as the pump will not function correctly.

ELECTRICAL CONNECTIONS

1- The electrical installation work must be carried

out by a qualiﬁed electrician.

The electrical installation must comply with the

standards in force in the country concerned

2- The power supply must be of the class 1 type. The

unit must be connected via an earthed connection

box. The electric power circuit must be protected

by a high-sensitivity 30 mA diﬀerential circuit brea-

ker set at 20 A. The connection must be used solely

to power the SANICUBIC®. If the power lead on the

unit is damaged, it must be replaced by the manu-

facturer or its after-sales service to avoid all danger.

OPERATING PRINCIPLE

- SANICUBIC® 1/SANICUBIC® 1® WP contains 1

pump equipped with a high performance shred-

ding system.

- SANICUBIC® 2 Classic/SANICUBIC® 2 Pro contains

two independent pumps. Each of these pumps is

equipped with a high performance shredding system.

Both pumps operate alternately to ensure even

ware. In case of surcharge operation, both motors

run simultaneously (or if one pump fails, the other

takes over).

- SANICUBIC® 2 XL contains two independent

pumps, each with a clearance of 55 mm.

The tank is equipped with three dip tubes, two of

which control motor activation for double security,

and the third controls the alarm system.

• 2 Long dip tubes

During normal operation, as soon as the eﬄuents

reach the long tube’s activation level in the tank,

the pumping system switches on.

• Short dip tube

During surcharge operation, if the eﬄuents reach

the highest level in the tank (short tube), an au-

dible and visual alarm system is activated and the

pumping system switches on (if it is not faulty).

COMMISSIONING

1- Once the plumbing and electrical connections

have been made, check that the connections

are watertight by letting water ﬂow successively

through each inlet used. Make sure that the unit

is operating correctly by carrying out at least two

start cycles with water to test the system.

2 - WARNING! Do not operate the motors manual-

ly (using the key pad) where no water has ente-

red the SANICUBIC®. Operation without water

damages the maceration system.

CONTROL BOX OPERATION

SANICUBIC® 1 CONTROL KEYPAD OPERATION (IP67)

1/ General alarms:

Level alarm:

If the water level inside the device is abnormally

high, the high level diptube microswitch will acti-

vate the motor and the alarm LED lights up red. If

this LED ﬂashes red, it indicates a detection pro-

blem for the normal water level (Long dip tube).

Time alarm:

If the motor runs continuously for more than 1

minute, the red LED alarm lights up.

2/ Reset alarm:

The button on the keypad will only allow you to

turn oﬀ the red LED (it will turn green) if the pro-

blem that triggered the alarm has been resolved.

It also allows you to stop the buzzing from the

remote alarm control.

Mains alarm:

- If the LED is oﬀ, there is no power supply.

- When the device is powered on again, and the

LED ﬂashes green, this indicates that the mains vol-

tage has temporarily disappeared.

OPERATION OF THE SANICUBIC® 1 WP REMOTE

CONTROL BOX

OPERATION OF THE ALARM

1/ General alarms:

Level alarm:

If the water level inside the device is abnormally

high: the buzzer is triggered + the red alarm LED

lights up + the motor starts-up. If this LED ﬂashes

red, it indicates a detection problem for the normal

water level (Long dip tube).

Temporary alarm:

If the motor runs for more than 1 minute: the buz-

zer is triggered + the red alarm LED lights up.

Mains alarm:

In case of power failure (or when unplugging the

device): the buzzer is triggered + the red alarm LED

lights up + the yellow mains LED ﬂashes.

2/ General alarm reset:

If the problem that triggered an alarm above di-

sappears, the buzzer stops, but the red alarm LED

remains lit as a reminder of the fact that the system

encountered a problem.

The keypad key will stop the buzzer in all cases,

but it will only turn oﬀ the red LED if the problem

that triggered the alarm has been resolved. Alarms

from the remote box also remain active until the

problem has been solved. This prevents the system

from being «abandoned» by default.

OPERATION OF THE SANICUBIC® 2 Classic/

SANICUBIC® 2 Pro/SANICUBIC® 2 XL REMOTE

CONTROL BOX

RAZ Alarme

LED

GREEN: Power on

RED: Alarm

BUTTON

Manual motor

activation

Alarm reset

Yellow LED

Mains supply

Red LED

alarme

Manual

activation

Yellow LED:

mains supply

Red LED:

alarm

Manual

activation

Motor 1

Manual

activation

Motor 2

Sanibroyeur SANICUBIC 2 Classic - 169 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info