489595
19
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
19
When a tape is played, the Digital
Auto Tracking system automatically
adjusts the tracking to obtain the
best possible picture. If noise bars
appear during playback, adjust the
tracking manually as follows:
Press the SET/TRACKING + or
button to obtain the best possible
picture. MANUAL TR. will appear
for 4 seconds on the screen.
To resume automatic tracking,
press the AUTO TRACKING button.
AUTO TR. will appear for 4 seconds on the screen.
Push the center of the tape until it is automatically
retracted into the TV/VCR.
AUTOMATIC POWER ON AND PLAY
When loading a cassette tape without the erase preven-
tion tab intact, the TV/VCR will turn on automatically
and playback will start immediately.
Insert the cassette with its labeled side facing you.
An inverted video cassette cannot be inserted.
AUTOMATIC EJECT
If the TV/VCR automatically rewinds the tape to the
beginning (AUTO REWIND FEATURE), the tape will
be ejected automatically (See NOTE on page 20).
NOTES: Always eject the tape when not in use.
The cassette tape can be ejected even if the
POWER is OFF.
To unload a video cassette, press
the EJECT button on the remote
control, or press the STOP/EJECT
button on the TV/VCR twice.
The first press will stop the tape in
any mode. The second press will
eject the tape.
After recording, break off the erase prevention tab if
you do not wish to record over the tape.
Cover the hole with adhesive tape.
Be careful the tape does not extend past the edges of
the video cassette housing.
Use only video cassette tapes marked
.
To play a prerecorded tape.
NOTE: This TV/VCR selects the playback tape speed
SP, LP or SLP automatically.
Load a prerecorded tape (When
loading a cassette tape without the
erase prevention tab, playback will
start automatically).
Press the PLAY button to begin
playback.
will appear on the screen.
Press the REW (Rewind) or F.FWD (Fast Forward)
button in the Stop mode.
or will appear on the screen.
FORWARD/REVERSE PICTURE SEARCH
If you want to see the tape during REW or FWD mode,
press and hold the REW or F.FWD button. The back-
ward or forward visual search picture will be seen on the
screen. Release to return to the REW or FWD mode.
MANUAL TR.
+
AUTO TR
.
Press the TV MONI. button while in the playback mode.The
video tape will continue to play while the picture switches to
the TV channel selected on the TV/VCR. Press the button
to return to the playback picture.
Press the STOP button once.
The tape will stop, but remain fully
loaded and ready to play.
will appear on the screen.
LOADING AND UNLOADING
LOADING
UNLOADING
TO PREVENT ACCIDENTAL ERASURE
TO RECORD AGAIN
Erase prevention tab
Screwdriver
Adhesive tape
PLAYBACK
TO START PLAYBACK
TO STOP PLAYBACK
TO REWIND OR FORWARD THE
TAPE RAPIDLY
DIGITAL TRACKING CONTROLS
TO MONITOR A TV PROGRAM
5A30501A E P18-25 12/09/2001, 17:3019
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sansui COM3100C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info