489557
15
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
15
Setting the on-screen
language
You can choose from three different languages
(English, French and Spanish) for the on-screen
displays.
Select the language you prefer first, then
proceed with the other menu options.
1
To turn on the TV, press POWER.
(POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.)
2
Press TV/DVD to select TV mode.
3
Press SETUP/TV MENU. The TV menu screen
will appear.
4
Press or to select “Setup”, then press or
ENTER.
5
Press or to select “Language”.
Video Label >>
Backlight
Auto Shut Off Off
Reset >>
16
Setup
Closed Caption >>
Language English
: Adjust
: Select
NOTE:
When you press SETUP/TV MENU first time after
purchase this LCD TV, above screen will appear
automatically.
6
Press or to select the desired language:
English, French (Français) or Spanish (Español).
7
Press EXIT/CANCEL to return to the normal
screen.
NOTE:
If no buttons are pressed for more than about 60
seconds, the menu screen will return to normal
operation automatically.
Memorizing channels
This TV is equipped with a channel memory
feature which allows channels to skip up or down
to the next channel set into memory, skipping
over unwanted channels. Before selecting
channels, they must be programmed into the
TV’s memory. To use this TV with an antenna, set
the Signal Type option to the Air mode. When
shipped from the factory, this menu option is in
the Cable mode.
Air/Cable selection
1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
Press or to select “Channel”, then press
or ENTER.
3
Press or to select Auto Ch Memory”, then
press or ENTER.
4
Press or to select “Signal Type”.
5
Press or to select Air” or “Cable”.
Air - VHF/UHF channels
Cable - CABLE TV channels
Automatic Search Start
Auto Ch Memory
Signal Type Cable
: Adjust
: Select
6
Press EXIT/CANCEL to return to the normal
screen.
CABLE CHART
The chart below is typical of many cable system
channel allocations.
NOTE:
It may take a few seconds for a digital channel
picture to appear on screen after being selected.
Automatic search
1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
Press or to select “Channel”, then press or
ENTER.
3
Press or to select Auto Ch Memory”, then
press or ENTER.
4
Press or to select Automatic Search”, then
press or ENTER.
Auto Ch Memory
Signal Type Cable
Digital Channel Found : 0
Analog Channel Found : 0
: Select
ENTER:Cancel
Automatic Search Stop
5
The TV will begin memorizing all the channels
available in your area.
It may take from 15 minutes to 30 minutes to
complete memorizing digital cable channels.
Depending on the reception condition, a bar
display may not advance for several minutes,
please be patient.
51H0201A_eng.indd 1551H0201A_eng.indd 15 08.3.6 2:54:34 PM08.3.6 2:54:34 PM
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sansui HDLCDVD220 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info