Bedienungsanleitung Sanyo PDG-DET100L (Seite 71 von 92) (Englisch)

470265

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

1. Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.

2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly

connected.

3. Make sure that all power is switched on.

4. If the projector still does not produce an image, restart your computer.

5. If an image still does not appear, disconnect the projector from your computer and check your computer

monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.

(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the

projector. Turn on equipment in the order of the projector and computer.)

6. If a problem still persists, check the following solutions.

Appendix

Problem: Solutions

No power.

– Plug the power cord of the projector into the AC outlet.

– Turn the MAIN ON/OFF switch to ON.

– Press the ON/STAND-BY Button to ON.

– Make sure the POWER indicator lights.

– Check the indicators. If the LAMP indicator lights and the other indicators blink, the

projector cannot be turned on. (Refer to page 70.)

– Check the projection lamp. (Refer to page 66.)

PIN code dialog box

appears at start-up.

– PIN code lock is being set. Enter a PIN code; the “1234” or numbers you have set (see

pages 24, 58-59)

The initial display is not

shown.

– Make sure “Off ” or “Countdown Off” are not chosen at Display function.

(See “SETTING” section on page 49)

The initial display is not

same with the default

one.

– Make sure “User” or “Off” are not chosen at Logo select function.

(See “SETTING” section on page 54)

When the projector is on

and you press the input

button, an icon other

than the Lamp mode icon

appears.

– That is the Filter warning icon. Refer to page 61.

An icon other than Input

mode or Lamp mode icon

appears.

– That is the Lamp replacement icon or the Filter warning icon. See pages 61, 66.

No image.

– Check the connection between your computer or video equipment and the projector.

– See if the input signal is correctly output from your computer. Some laptop computers

may need to be changed the setting for monitor output when connected to the

projector. See your computer’s instruction manual for the setting.

– It takes about 20 seconds to display an image after turning on the projector.

– See if the selected system is corresponding with your computer or video equipment.

– Select correct input source once again through menu operation (See pages 32, 42).

– Make sure the temperature is not out of Operating Temperature

(41˚F–104˚F [5˚C–

40˚C]).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PDG-DET100L Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo PDG-DET100L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info