Bedienungsanleitung Sanyo PDG-DWL2500 (Seite 68 von 82) (Englisch)

489447

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

This projector uses a high-pressure lamp which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

l Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee

of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than

other similar lamps.

l If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights

up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of

the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

l A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its

lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in

which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an

authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check

carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out

from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one

should check the inside of the projector except those who are authorized trained technicians and who

are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those

who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken

glass.

LAMP HANDLING PRECAUTIONS

Maintenance and Cleaning

Resetting the Lamp Counter

Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP

REPLACE indicator stops lighting and the Lamp replacement icon disappears.

4Note:

Do not reset the Lamp counter without implementing

lamp replacement. Be sure to reset the Lamp counter

only after replacing the lamp.

Lamp replacement

counter Reset?

appears.

Select Yes, then

another confirmation

box appears.

Select Yes again

to reset the Lamp

counter.

Press the MENU button to display the On-Screen

Menu. Use the Point ed buttons to select Setting

and then press the Point 8 or the SELECT button.

Use the Point ed buttons to select Lamp counter

and then press the SELECT button. Use the Point

ed buttons to select Lamp counter reset and then

press SELECT button. Lamp replacement counter

Reset? appears. Select Yes to continue.

Another confirmation dialog box appears, select Yes

to reset the Lamp counter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PDG-DWL2500 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo PDG-DWL2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info