Bedienungsanleitung Sanyo plc xc55 (Seite 18 von 80) (Englisch)

215899

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Basic Operation

Connect the projector’s AC power cord into an AC

outlet. The POWER indicator becomes red.

Press the POWER ON/STAND-BY button on the

top control or on the remote control. The POWER

indicator becomes green and the cooling fans start

to operate. The preparation display appears on the

screen and the count down starts.

After the countdown, the input source that was

selected the last time and the Lamp mode status icon

(see page 51) appears on the screen.

Complete peripheral connections (with a computer,

VCR, etc.) before turning on the projector.

Turning On the Projector

To Enter a PIN code

Select a number by pressing the Point ▲▼ buttons,

and then press the Point ►button to fix the number

and move the pointer. The number changes to "". If

you fixed an incorrect number, move the pointer to the

number you want to correct by pressing the Point ◄

button, and then select the correct number by pressing

the Point ▲▼ buttons.

Repeat this step to complete entering a four-digit

number.

"1234" is set as the initial PIN code at the factory.

After entering the four-digit number, move the pointer

to "Set" by pressing the Point ►button. Press the

SELECT button so that you can start to operate the

projector.

If you entered an incorrect PIN code, "PIN code" and

the number () turns red. Enter the correct PIN

code all over again.

What is PIN code?

PIN (Personal Identification Number) code that allows

the person who knows it to operate the projector.

Setting a PIN code prevents unauthorized use of the

projector.

A PIN code consists of a four-digit number. Refer to the

PIN code lock function in the Setting on pages 53 and

54 for locking operation of the projector with your PIN

code.

CAUTION ON HANDLING PIN CODE

If you forget your PIN code, the projector can no longer

be started. Set a new PIN code with special care,

write it down in column on page 79 of this manual, and

keep it on hand. Should the PIN code be missing or

forgotten, consult your dealer or service center.

The preparation display disappears after 30

seconds.

(See page 51 for Lamp mode.)



Note:

The Filter warning and Lamp replacement icons

may appear on the screen depending on the

usage state of the projector.

Selected Input Source and Lamp Mode

Lamp mode

After th e OK ic o n

disappears, you can

operate the projector.

PIN Code Input Dialog Box

If the projector is locked with a PIN code, PIN code

Input Dialog Box appears. Enter the PIN code as

instructed below.

Notes:

• When the Input Search function is set

On1 or On2, the input signal will be

searched automatically (p.46)

• When the Logo select function is off,

the logo is not shown on the screen.

(p.48)

• When the "Countdown off" or "Off" is

selected in the Display function, the

countdown is not shown on the screen.

(p.47)

• During the countdown period, all

operations are invalid.

• If the PIN code number is not input for

three minutes after the PIN code dialog

box appeared, the projector is turned off

automatically.

Basic Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xc55 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo plc xc55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info