Bedienungsanleitung Sanyo plc xf47 (Seite 23 von 79) (Englisch)

215459

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

Turning On the Projector

Connect the projector’s AC power cord into an AC

outlet and turn the MAIN ON/OFF Switch to ON. The

LAMP indicator lights red and the READY indicator

lights green.

Press the ON/STAND-BY button on the side control

or on the remote control. The LAMP indicator

dims red and the cooling fans start to operate. The

preparation display appears on the screen and the

countdown starts.

The preparation display will disappear after 20

seconds.

After the countdown, the input source that was

selected the last time and the Lamp mode icon (see

page 56) appear on the screen.

If the projector is locked with a PIN code, PIN code

Input Dialog Box will appear. Enter the PIN code as

instructed below.

Selected Input Source and Lamp control

Complete peripheral connections (with a computer,

VCR, etc.) before turning on the projector.

What is PIN code?

PIN (Personal Identification Number) code is a security

code that allows the person who knows it to operate the

projector. Setting a PIN code prevents unauthorized use

of the projector.

A PIN code consists of a four-digit number. Refer to the

PIN code lock function in the Setting Menu on page 52-

53 for locking operation of the projector with your PIN

code.

PIN code Input Dialog Box

Enter a PIN code

CAUTION ON HANDLING PIN CODE

If you forget your PIN code, the projector

can no longer be started. Take special care

in setting a new PIN code; write down the

number in a column on page 75 of this

manual and keep it at hand. Should the

PIN code be missing or forgotten, consult

your dealer or service center.

After the OK icon

disappears, you can

operate the projector.

Lamp mode

See page 56 for the Lamp control status

✔Note:

• The Lamp replacement icon and the Filter

warning icon may appear on the screen

depending on the usage state of the projector.

Use the Point ed buttons on the side control or on the

remote control to enter a number. Press the Point 8

button to fix the number and move the red frame pointer

to the next box. The number changes to “✳.” Repeat

this step to complete entering a four-digit number. After

entering the four-digit number, move the pointer to “Set.”

Press the SELECT button so that you can start to operate

the projector.

If you fixed an incorrect number, use the Point 7 button

to move the pointer to the number you want to correct,

and then enter the correct number.

If you entered an incorrect PIN code, “PIN code” and the

number (✳✳✳✳) will turn red for a moment. Enter the

correct PIN code all over again.

✔Note:

• When the Logo select function is set to “Off,” the

logo will not be shown on the screen (p.48).

• When the “Countdown off” or “Off” is selected

in the Display function, the countdown will not

be shown on the screen (p.47).

• During the countdown period, all operations are

invalid.

• If the correct PIN code number is not entered

within three minutes after the PIN code dialog

box appeared, the projector will be turned off

automatically.

• The “1234” is set as the initial PIN code at the

factory.

Basic Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xf47 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info