Bedienungsanleitung Sanyo plc xf47 (Seite 62 von 79) (Englisch)

215459

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

1. Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.

2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly

connected.

3. Make sure that all power is switched on.

4. If the projector still does not produce an image, restart your computer.

5. If an image still does not appear, disconnect the projector from your computer and check your computer

monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.

(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the

projector. Turn on equipment in the order of the projector and computer.)

6. If a problem still persists, check the following solutions.

Appendix

Problem: Solutions

No power.

– Plug the power cord of the projector into the AC outlet.

– Turn the MAIN ON/OFF switch to ON.

– Press the ON/STAND-BY Button to ON.

– Make sure the READY Indicator lights.

– Check the WARNING TEMP. and the READY indicator. If both the WARNING TEMP. and

the READY indicator flashes, a projector cannot be turned on.

(See "TURNING ON/OFF THE PROJECTOR" section on pages 23-24.)

– Check the projection lamp. (Refer to page 57.)

Image is out of focus.

– Adjust focus of the projector.

– Check Projection Lens to see if it needs cleaning.

✔Note: Moving a projector from a cool temperature location to a warm temperature

location may result in moisture condensation on Projection Lens. In such cases,

leave the projector OFF and wait until condensation evaporates.

Picture is Left/Right

reversed.

– Check the Ceiling / Rear function. (See page 43.)

Picture is Top/Bottom

reversed.

– Check the Ceiling function. (See page 43)

Some displays are not

seen during Operation.

– Check the Display function. (See “SETTING” section on page 47.)

No image.

– Check the connection between your computer or video equipment and a projector.

– It takes about 20 seconds to display an image after turning on the projector.

– See if the selected system is corresponding with your computer or video equipment.

– Make sure the temperature is not out of Operating Temperature

(41˚F–95˚F [5˚C–35˚C]).

The initial display is not

shown.

– Make sure “Off ” or “Countdown Off” are not chosen at Display function.

(See “SETTING” section on page 47)

The initial display is not

same with the default

one.

– Make sure “User” or “Off” are not chosen at Logo select function.

(See “SETTING” section on page 48)



appears on the screen

–

The end of lamp life is approaching. Replace the lamp with a new one promptly.

(See page 57)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xf47 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info