Bedienungsanleitung Sanyo PLC-XL51 (Seite 20 von 77) (Englisch)

489448

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

Connect the projector’s AC power cord into an AC

outlet. The POWER indicator turns red.

Press the ON/STAND-BY button on the top control or

on the remote control. The POWER indicator becomes

green and the cooling fans start to operate. The

preparation display appears on the screen and the

count down starts.

The preparation display disappears after 30 seconds.

After the countdown, the input source that was

selected the last time and the Lamp mode status icon

(see page 51) will appear on the screen.

If the projector is locked with a PIN code, a PIN code

Input Dialog Box appears. Enter the PIN code as

instructed below.

See page 51 for the Lamp mode.

Selected Input Source and Lamp Mode

Complete peripheral connections (with a computer,

VCR, etc.) before turning on the projector.

Lamp mode

After the OK icon

disappears, you can

operate the projector.

PIN Code Input Dialog Box

Turning On the Projector

Basic Operation

Enter a PIN code

Select a number by pressing the Point ed buttons, and

then press the Point 8 button to fix the number and move

the pointer. The number changes to "✳". If you fixed an

incorrect number, move the pointer to the number you want

to correct by pressing the Point 7 button, and then select

the correct number by pressing the Point ed buttons.

Repeat this step to complete entering a four-digit number.

"1234" is set as the initial PIN code at the factory.

After entering the four-digit number, move the pointer to

"Set" by pressing the Point 8 button. Press the SELECT

button so that you can start to operate the projector.

If you entered an incorrect PIN code, "PIN code" and the

number (✳✳✳✳) turns red. Enter the correct PIN code all

over again.

What is PIN code?

PIN (Personal Identification Number) code is a security

code that allows the person who knows it to operate the

projector. Setting the PIN code prevents unauthorized use

of the projector.

A PIN code consists of a four-digit number. Refer to the PIN

code lock function in the Setting Menu on pages 52-53 for

locking operation of the projector with your PIN code.

✔Note:

• When the Input Search function is set

to On2, the input signal will be searched

automatically (p.49).

• When the Logo select function is "Off,” the

logo will not be displayed on the screen

(p.47).

• When the "Countdown off" or "Off" is selected

in the Display function, the countdown will

not be shown on the screen (p.46).

• During the countdown period, all operations

are invalid.

• If the PIN code number is not entered for

3 minutes after the PIN code dialog box

appeared, the projector will be turned off

automatically.

CAUTION ON HANDLING THE PIN CODE

If you forget your PIN code, the projector can no

longer be started. Take a special care in setting a

new PIN code; write down the number in a column

on page 75 of this manual and keep it at hand.

Should the PIN code be missing or forgotten,

consult your dealer or service center.

✔Note:

• The Lamp replacement icon and the Filter

warning icon may appear on the screen

depending on the usage state of the

projector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PLC-XL51 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info