Bedienungsanleitung Sanyo plc xl51 (Seite 65 von 77) (Englisch)

215777

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

– Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18.

– Make sure all equipment is connected to the AC outlet and the power is turned on.

– When you operate the projector with a computer and it does not project an image, restart the computer.

Appendix

Problem:

– Solutions

No power

– Plug the power cord of the projector into the AC outlet.

– See if the POWER indicator lights red.

– Wait until the POWER indicator stops blinking to turn on the projector

again. The projector can be turned on after the POWER indicator turns red.

(see page 21).

– Check the WARNING indicator. If the WARNING indicator lights red, the

projector cannot be turned on (see on page 60).

– Check the projection lamp (see page 63).

– Check if the projector is installed in proper position. (See page 7)

– Unlock the Key lock function for the projector. See page 51.

PIN code dialog box appears at

start-up.

– PIN code lock is being set. Enter a PIN code; the “1234” or numbers you

have set (see pages 20, 52-53)

The initial display is not shown.

– Make sure “Off ” or “Countdown Off” are not chosen at Display function.

(See “SETTING” section on page 46)

The initial display is not same with

the default one.

– Make sure “User” or “Off” are not chosen at Logo select function.　(See

“SETTING” section on page 47)

Input signal switches automatically.

(or does not switch automatically)

– Make sure Input search function is adjusted properly. See page 49.

When the projector is on and you

press the input button, an icon other

than the Lamp mode icon appears.

– That is the Filter warning icon. Refer to page 55.

An icon other than Input mode or

Lamp mode icon appears.

– That is the Lamp replacement icon or the Filter warning icon. See page

54.

No image

– Check the connection between your computer or video equipment and the

projector (see pages 16-18).

– See if the input signal is correctly output from your computer. Some laptop

computers may need to be changed the setting for monitor output when

connected to the projector. See your computer’s instruction manual for the

setting.

– It takes about 30 seconds to display an image after turning on the

projector.

– See if the selected system is corresponding with your computer or video

equipment (see pages 28, 39).

– Select correct input source once again through menu operation (see pages

27, 37–38).

– Make sure the temperature is not out of the specified operating

temperature (41 ˚F–104 ˚F [5 ˚C–40 ˚C]).

– When "No Show" is operating, the image can not be displayed. Press the

NO SHOW button or any other button on the remote control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xl51 Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info