Bedienungsanleitung Sanyo plc xp100l (Seite 64 von 81) (Englisch)

214883

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

1. Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.

2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly

connected.

3. Make sure that all power is switched on.

4. If the projector still does not produce an image, restart your computer.

5. If an image still does not appear, disconnect the projector from your computer and check your computer

monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.

(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the

projector. Turn on equipment in the order of the projector and computer.)

6. If a problem still persists, check the following solutions.

No power.

● Plug the power cord of the projector into the AC outlet.

● Wait until the POWER indicator stops blinking to turn on the projector again. (See page

23)

● Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator is blinking, the

projector cannot be turned on. (See page 63.)

● Check the projection lamp. (See page 59.)

● Unlock the Key lock function for the projector. (See page 53)

● See if the filter cartridge is inserted. (See page 57)

Image is out of focus.

● Adjust the focus of the projector.

● Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.

● Check the projection lens to see if it needs cleaning.

NOTE: Moving the projector from a cool to a warm place may result in moisture

condensation on the projection lens. If this happens, leave the projector off and

wait until condensation evaporates.

Picture is left/right

reversed.

● Check the Ceiling/Rear function. (See pages 40, 44)

Problem: Try These Solutions

Picture is top/bottom

reversed.

● Check the Ceiling function. (See pages 40, 44.)

Some displays are

not seen during

operations.

● Check the Display function. (See page 48.)

No image.

● Check the connection between your computer or video equipment and the projector.

● It takes about 30 seconds to display an image after turning on the projector.

● See if the selected system is corresponding with your computer or video equipment.

● Make sure the temperature is not out of specified operating temperature (41˚F–104˚F

[5˚C–40˚C]).

Appendix

appears on the

screen

● The end of lamp life is approaching. Replace the lamp with a new one promptly. (See

page 59)

appears on the

screen

● The filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages

56-57)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xp100l Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo plc xp100l

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info