Bedienungsanleitung Sanyo plc xp100l (Seite 70 von 81) (Englisch)

214883

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Indicators

Projector Condition

POWER

green

LAMP

red

WARNING

TEMP.

red

WARNING

FILTER

orange

LAMP

REPLACE

orange

The projector has been cooled down enough and the

temperature returns to normal. When turning on the projector,

the WARNING TEMP. indicator stops blinking. Check and

replace the filter.

The lamp cannot light up. (The projector is preparing for stand-

by or the projection lamp is being cooled down. The projector

cannot be turned on until cooling is completed.)

The lamp cannot light up. (The lamp has been cooled down

enough and the projector is in stand-by mode and ready to be

turned on with the ON/STAND-BY button.)

The lamp has been used overtime. Replace the lamp

immediately and then reset the lamp counter. The indicator

will be turned off after resetting the counter.

If the Filter counter reached a time set in the timer setting,

a Filter replacement icon (Fig.2) appears on the screen and

the WARNING FILTER indicator on the top panel lights up.

Replace the filter as soon as possible. If the filter is out of

scroll and the projector reaches a time set in the timer setting,

Fig. 3 appears on the screen and the WARNING FILTER

indicator lights up. Replace the filter cartridge as soon as

possible.

If the filter is clogged and no scroll is left in the filter cartridge,

a Filter cartridge replacement icon (Fig.4) appears on the

screen and the WARNING FILTER indicator lights up. Replace

the filter cartridge as soon as possible.

✔Note:

• Fig.2, Fig.3 and Fig.4 icon will not appear when the Display function

is set to “Off” (p.48), during “Freeze” (p.28), or “No show” (p.29).

The filter cartridge is not installed in the projector. Check the

filter compartment to see if the filter cartridge is installed in

the projector. When the filter cartridge is installed and the

indicators continue to light and blink, read the column below.

The projector detects an abnormal condition and cannot be

turned on. Unplug the AC power cord and plug it again to turn

on the projector. If the projector is turned off again, unplug the

AC power cord and contact the dealer or the service center.

Do not leave the projector on. It may cause an electric shock

or a fire hazard.

Fig.2 Filter replacement icon

When the filter detects clogging, reaches a time set in the timer setting or runs out of the filter scroll, the WARNING

FILTER indicator lights orange. When this indicator lights orange, replace the filter or the filter cartridge with a new

one promptly. Reset the Filter counter after replacing the filter (p.58). Reset the Filter counter and Scroll counter after

replacing the filter cartridge (p.58).

When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights

orange. When this indicator lights

orange, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp (p.59).

Fig.4 Filter cartridge replacement icon

✽

Appendix

Fig.3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xp100l Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo plc xp100l

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info