Bedienungsanleitung Sanyo plc xu105 (Seite 52 von 71) (Englisch)

215461

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

This function provides the following options in the cooling

fans’ operation when the projector is turned off (p.20).

L1 ...... Normal operation

L2 ...... Slower and lower-sound than the normal operation

(L1), but it takes more time to cool the projector

down.

Fan

Setting

Fan control

Fan

Warning log

This function records anomalous operations while the

projector is in operation and use it when diagnosing faults.

Up to 10 warning logs are displayed with the latest warning

message at the top of the list, followed by previous warning

messages in chronological order.

Note:

• When the Factory default function is executed, all the

warning log records will be deleted.

This function is used to reset the lamp counter.

When the lamp life is left less than 100 hours, the Lamp

replacement icon (Fig.1) will appear on the screen, indicating

that the end of lamp life is approaching.

When the lamp life is left 0 hour, the Lamp replacement icon

(Fig.2) will appear on the screen, indicating that the end of

lamp life is reached.

When replacing the projection lamp, reset the lamp counter.

See "Resetting the Lamp Counter" on page 58.

Lamp counter

This icon appears on the screen when the end of

lamp life is approaching.

This icon appears on the screen when the end of

lamp life is reached.

Fig.1

Lamp replacement icon

Fig.2

Lamp replacement icon

Note:

• This icon also appears at turning on and

selecting input source.

Note:

• At turning on, the icon (Fig.2) will appear.

At selecting input source, the icon (Fig.1)

will appear.

Note:

• The Lamp replacement icons (Fig.1 and Fig.2) will not

appear when the Display function is set to “Off” (p.44),

during “Freeze” (p.25), or “No show” (p.26).

0º

180º

0º

180º

-50º

GOOD

+50º

40º

50º50º

40º

Fan Control Setting

On 1

Choose the running speed of cooling fans from the following

options according to the ground elevation under which you

use the projector.

Off.......Normal speed. Set this function to “Off” when using

the projector in non-high altitude environment.

On 1... Faster than Off mode. Select this mode when using

the projector in high altitudes (about 1,200 meters

or more above the sea level) where the fans have

less cooling effect.

On 2....Faster than On 1 mode. Select this mode when

using the projector in higher altitudes than above

where the fans have lesser cooling effect.

On 3....Be sure to set the Lamp control in High and the Fan

control in On 3 when using the projector inclined

at between +40 degrees to +140 degrees to the

horizontal plane at altitudes between 0 and

approximately 1,600 meters above sea level.

Note:

• The fan noise becomes louder in On 1 ,On2 and On3.

• Setting “Fan control” to On1 ,On2 or On3 affects L2

operation in “Fan.”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo plc xu105 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info