Bedienungsanleitung Sanyo PLV-1080HD (Seite 42 von 60) (Englisch)

489695

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Filter counter

This function is used to set a frequency for the filter cleaning.

When the projector reached a specified time between cleanings, a

Filter warning icon appears on the screen, notifying the cleaning is

necessary.

Use the Point

8 button to select the desired timer [Off/ 50H/ 100H/

200H/ 300H/ 400H/ 500H] and press the OK button. After cleaning

the filter, be sure to select [Reset] and set the timer. The Filter

warning icon will not turn off until the filter counter is reset.

For details about resetting the timer, refer to “Resetting the Filter

Counter” on page 48.

Test pattern

A test pattern for zoom and focus adjustment is available for use

when setting up the projector.

Filter counter

Use the Point

8 button to select

the timer from (Reset/Off/

50H/ 100H/ 200H/ 300H/ 400H/

500H) depending on the use

environment.

Filter warning icon appears on the screen at a set

time.

✔Note:

 •ThePowermanagementfunctioncannotbeoperatedduring

cleaning.

Cleaning

This function is used to clean the inside of the projector. Using a

blower at the same time is more effective. See page 46.

Press the Point

8 or OK buttons, then the projected image is

blacked out temporarily regardless of whether or not an input

source is selected.

To cancel the cleaning function, set the projector back into

the right position, then press any other button during cleaning

operations.

Factory default

This function restores all setting values except for the user’s logo,

the filter counter and the lamp time to the factory default settings.

Select [Yes] and press the

OK button, then another

confirmation box appears.

Factory default

Select Factory default and

press the Point

8 or OK

buttons. “Return to Factory

default?” appears.

Select [Yes] again to

restore to the factory

default settings.

Choose the running speed of cooling fans from the following

options according to the environment, where there is a drastic

elevation of room temperature while the projector is being used.

Normal ....... Normal speed.

Mode 1 ...... Faster than Normal mode. Use this mode when you

want to increase the cooling effect when operating

the projector in the environment, where there is a

drastic elevation of room temperature.

Mode 2 ...... Faster than Mode 1 mode. Use this mode when you

want to increase the cooling effect when operating

the projector in the environment, where there is a

more drastic elevation of room temperature.

Fan control

This function resets the lamp replacement counter. When

replacing the projection lamp, reset the lamp replacement counter

with this function. See page 50 for operation.

Lamp counter reset

For technician use ONLY. Set this function to Off.

Service port

Setting

✔Note:

 •TheFilterwarningiconwillnotappearwhen

theDisplayfunctionissetto“Off”(p.40),during

“Freeze”(p.23),“Noshow”(p.23),“Color

management”(p.32),“Testpattern”(p.42),

“Rename”(p.39),“Customgamma”(p.31),or

“Cleaning”(p.42).

✔Note:

 •FannoisebecomeslouderinMode1andMode2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PLV-1080HD Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info