Bedienungsanleitung Sanyo PT-RS11K (Seite 125 von 219) (Englisch)

598873

125

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

Chapter 4 Settings — [PROJECTOR SETUP] menu

ENGLISH - 125

[PROJECTOR SETUP] menu

On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the sub-

menu.

Refer to “Navigating through the menu” (x page 76) for the operation of the menu screen.

[PROJECTOR ID]

The projector has an ID number setting function that can be used when multiple projectors are used side by side

to enable simultaneous control or individual control via a single remote control.

1) Press as to select [PROJECTOR ID].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[ALL] Select this item when controlling projectors without specifying an ID number.

[1] - [64] Select this item when specifying an ID number to control individual projector.

Note

f To specify an ID number for individual control, the ID number of a remote control must match the ID number of the projector.

f When the ID number is set to [ALL], the projector will operate regardless of the ID number specied during remote control or computer

control.

If multiple projectors are set up side by side with IDs set to [ALL], they cannot be controlled separately from the projectors with other ID

numbers.

f Refer to “Setting ID number of the remote control” (x page 74) for how to set the ID number on the remote control.

[PROJECTION METHOD]

Set the projection method in accordance with the installation status of the projector.

Change the projection method if the screen display is upside down or inverted.

1) Press as to select [PROJECTION METHOD].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[FRONT/FLOOR] When installing the projector on the desk, etc., in front of the screen

[FRONT/CEILING] When installing the projector in front of the screen using the Ceiling Mount Bracket (optional)

[REAR/FLOOR] When installing the projector on the desk, etc., behind the screen (with a translucent screen)

[REAR/CEILING]

When installing the projector behind the screen (with a translucent screen) using the Ceiling Mount

Bracket (optional)

[OPERATION SETTING]

Set the operation method of the projector.

The settings are reected when “Initial setting (operation setting)” (x page 57) in the [INITIAL SETTING]

screen is already set.

If you change the settings while using the projector, the duration until the luminance of light source decreases by

half may shorten or the luminance may decrease.

Setting [OPERATING MODE]

1) Press as to select [OPERATION SETTING].

2) Press the <ENTER> button.

f The [OPERATION SETTING] screen is displayed.

3) Press as to select [OPERATING MODE].

4) Press qw to switch the item.

f The items will switch each time you press the button.

[NORMAL]

Set this item when high luminance is required. The estimated runtime is approximately 20 000 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PT-RS11K Seite 125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo PT-RS11K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info