Bedienungsanleitung Sanyo PT-RS11K (Seite 135 von 219) (Englisch)

598873

135

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

Chapter 4 Settings — [PROJECTOR SETUP] menu

ENGLISH - 135

Note

f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the no signal lights-out function is operating and the light source

is turned off.

f When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on

again from the condition that the light source has turned off by this function.

g When the signal is input

g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed

g When the power on <b> button is pressed

g When the operation to disable the shutter function (shutter: open) is performed, such as pressing the <SHUTTER> button

g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up

[INITIAL STARTUP]

Set the startup method when the <MAIN POWER> switch is set to <ON>.

1) Press as to select [INITIAL STARTUP].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[LAST MEMORY] Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.

[STANDBY] Starts up the projector in standby.

[ON] Starts projecting immediately.

[STARTUP INPUT SELECT]

Set the input when the projector is switched on to start projection.

1) Press as to select [STARTUP INPUT SELECT].

2) Press the <ENTER> button.

f The [STARTUP INPUT SELECT] screen is displayed.

3) Press asqw to select the input, and press the <ENTER> button.

[LAST USED] Keeps the input selected last.

[RGB1] Sets the input to RGB1.

[RGB2] Sets the input to RGB2.

[DVI-D] Sets the input to DVI-D.

[HDMI] Sets the input to HDMI.

[DIGITAL LINK] Sets the input to DIGITAL LINK.

[SDI1] Sets the input to SDI1.

[SDI2] Sets the input to SDI2.

[INPUT1] - [INPUT10]

Sets the input to DIGITAL LINK, and switches the input of the Panasonic twisted-pair-cable

transmitter to the specied input.

*1 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input

name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.

Note

f If [BACKUP INPUT MODE] in the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] (x page 110) is set to [1], and the power is

turned off with the input set to HDMI in the previous use, the projection will start with DVI-D input even when [STARTUP INPUT SELECT] is

set to [LAST USED].

f When [BACKUP INPUT MODE] is set to [2] using the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] (x page 110), and the

power is turned off with the input set to SDI2 in the pervious use, projection will start with the SDI1 input even if [STARTUP INPUT SELECT]

is set to [LAST USED].

[DATE AND TIME]

Set the time zone, date, and time of the built-in clock of the projector.

Setting the time zone

1) Press as to select [DATE AND TIME].

2) Press the <ENTER> button.

f The [DATE AND TIME] screen is displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PT-RS11K Seite 135

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo PT-RS11K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info