Bedienungsanleitung Sanyo PT-RS11K (Seite 140 von 219) (Englisch)

598873

140

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

Chapter 4 Settings — [PROJECTOR SETUP] menu

140 - ENGLISH

[OFF] Does not return the response when an ID is designated as GROUP.

Note

f When [INPUT SELECT] is set to [DIGITAL LINK], communication using that serial terminal is available only when the corresponding device

(such as the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G)) is connected to the <DIGITAL LINK/

LAN> terminal.

f When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for “NO

SIGNAL SLEEP” of the DIGITAL LINK output supported device should be set to “OFF” to avoid interruption of communication.

f When [INPUT SELECT] is set to [DIGITAL LINK], communication speed for input is xed to 9 600 bps and the parity is xed to “NONE”.

[REMOTE2 MODE]

You can set the <REMOTE 2 IN> terminal.

1) Press as to select [REMOTE2 MODE].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[DEFAULT]

Uses pin assignment of the <REMOTE 2 IN> terminal in standard setting. (x page 203)

[USER] Changes the setting of the <REMOTE 2 IN> terminal.

f When [USER] is selected, proceed to Step 3).

3) Press the <ENTER> button.

4) Press as to select one from [PIN2] to [PIN8], and press qw to switch the setting.

[FUNCTION BUTTON]

Set the function of the <FUNCTION> button on the remote control.

1) Press as to select [FUNCTION BUTTON].

2) Press the <ENTER> button.

f The [FUNCTION BUTTON] screen is displayed.

3) Press as to select a function.

[DISABLE] Disables the <FUNCTION> button.

[P IN P]

Switches the [P IN P] setting ([OFF], [USER1], [USER2], or [USER3]). (x page 146)

[SUB MEMORY]

Displays the sub memory list. (x page 151)

[SYSTEM SELECTOR]

Switches the [SYSTEM SELECTOR] setting. (x page 88)

[SYSTEM DAYLIGHT VIEW]

Switches the [SYSTEM DAYLIGHT VIEW] setting. (x page 86)

[FREEZE]

Temporarily pauses the image. (x page 123)

[WAVEFORM MONITOR]

Displays the waveform of the input signal. (x page 123)

[LENS MEMORY LOAD]

Loads the registered lens memory. (x page 141)

[LEFT/RIGHT SWAP]

Switches the [LEFT/RIGHT SWAP] setting. (x page 103)

[PROJECTION METHOD]

Switches the [PROJECTION METHOD] setting. (x page 125)

4) Press the <ENTER> button.

[LENS CALIBRATION]

Detect the lens shift limit value of the projector and set the home position and the ET-D75LE90 lens standard

position automatically.

1) Press as to select [LENS CALIBRATION].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[NORMAL]

Select this item when anything other than the Fixed-focus Lens (Model No.: ET-D75LE90) is used.

Move the lens to the home position after completing the calibration.

[D75LE90]

Select this item when the Fixed-focus Lens (Model No.: ET-D75LE90) is used.

Move the lens to the ET-D75LE90 lens standard position after completing the calibration.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo PT-RS11K Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sanyo PT-RS11K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info