Bedienungsanleitung Sanyo SAP-KMRV76EH (Seite 94 von 117) (Englisch)

489450

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

English

IMPORTANT!

Please Read Before Starting

This air conditioning system meets strict safety and oper-

ating standards. As the installer or service person, it is an

important part of your job to install or service the system

so it operates safely and efficiently.

For safe installation and trouble-free operation, you

must:

●

Carefully read this instruction booklet before beginning.

●

Follow each installation or repair step exactly as

shown.

●

Observe all local, state, and national electrical codes.

●

Pay close attention to all warning and caution notices

given in this manual.

This symbol refers to a hazard

or unsafe practice which can

result in severe personal injury

or death.

This symbol refers to a hazard

or unsafe practice which can

result in personal injury or

product or property damage.

If Necessary, Get Help

These instructions are all you need for most installation

sites and maintenance conditions. If you require help for

a special problem, contact our sales/service outlet or

your certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for

improper installation or maintenance service, including

failure to follow the instructions in this document.

SPECIAL PRECAUTIONS

When Wiring

ELECTRICAL SHOCK CAN CAUSE

SEVERE PERSONAL INJURY OR DEATH.

ONLY A QUALIFIED, EXPERIENCED

ELECTRICIAN SHOULD ATTEMPT TO

WIRE THIS SYSTEM.

• Do not supply power to the unit until all wiring and tub-

ing are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this

system. Carefully refer to the wiring diagram and these

instructions when wiring. Improper connections and

inadequate grounding can cause accidental injury or

death.

• Ground the unitfollowing local electrical codes.

• Connect all wiring tightly. Loose wiring may cause

overheating at connection points and a possible fire

hazard.

• Install a protective leakage breaker/fuse link depend-

ing on the installation location (especially a damp or

humid location). If a leakage breaker/fuse link is not

installed, electric shock can occur.

When Transporting

Be careful when picking up and moving the indoor and

outdoor units. Get a partner to help, and bend your knees

when lifting to reduce strain on your back. Sharp edges or

thin aluminum fins on the air conditioner can cut your fin-

gers.

When Installing…

…In a Ceiling or Wall

Make sure the ceiling/wall is strong enough to hold the

unit’s weight. It may be necessary to construct a strong

wood or metal frame to provide added support.

…In a Room

Properly insulate any tubing run inside a room to prevent

“sweating” that can cause dripping and water damage to

walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to provide

a solid, level foundation for the outdoor unit. This pre-

vents water damage and abnormal vibration.

When Connecting Refrigerant Tubing

• Do not add any refrigerant, air, or substance into the

refrigeration circuit other than the designated refriger-

ant (R410A). Adding anything other than the specified

refrigerant may cause the pressure to rise excessively

in the refrigeration circuit, rupturing the circuit and

causing injury or damage.

• Use all-new tubing and flare nuts to make the tubing

connections. Using any previous parts (from R22-

based systems) may result in damage to the equip-

ment, and may lead to the refrigeration circuit ruptur-

ing, causing a serious accident.

• Apply refrigerant lubricant to the matching surfaces of

the flare and union tubes before connecting them, then

tighten the nut with a torque wrench for a leak-free

connection.

• Check carefully for leaks before starting the test run.

When Servicing

• Turn the power OFF at the main power box (mains)

before opening the unit to check or repair electrical

parts and wiring.

• Keep your fingers and clothing away from any moving

parts.

• Clean up the site after you finish, remembering to

check that no metal scraps or bits of wiring have been

left inside the unit being serviced.

Others

• Ventilate any enclosed areas when installing or testing

the refrigeration system. Escaped refrigerant gas, on

contact with fire or heat, can produce dangerously

toxic gas.

• Confirm upon completing installation that no refrigerant

gas is leaking. If escaped gas comes in contact with a

stove, gas water heater, electric room heater or other

heat source, it can produce dangerously toxic gas.

WARNING

CAUTION

08-324 CMRV3656EH_IU EN 6/15/09 5:27 PM Page 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo SAP-KMRV76EH Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info