Bedienungsanleitung Sanyo SAP-KRV96EH (Seite 55 von 65) (Englisch)

639747

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

REMOTE CONTROL UNIT

Transmitter

When you press the buttons on the remote control unit, the mark

appears in the display to transmit the setting changes to the receiver

in the air conditioner.

Display

Information on the operating conditions is displayed while the remote

control unit is switched on. If the unit is turned off, FLAP setting and

FAN SPEED setting are not displayed.

FAN SPEED selector button

: The air conditioner automatically decides the fan speeds.

: High fan speed

: Medium fan speed

: Low fan speed

FLAP button

Press this button either to select the setting of the airflow direction to the

auto. flap in each mode or one of the six possible positions manually or to

select the sweep function which moves the flap up and down

automatically.

: Auto flap setting: If selected in a heating operation, the flap is set

to position (3) in the following chart. If selected in a cooling or dry

operation, the flap is set at position (7) in the following chart.

: The airflow direction can be set manually. (six positions)

: The flap moves up and down automatically.

When you press the FLAP button, the air flow direction will be changed

one by one as follows.

NOTE

SWEEP

CANCEL button

SENSOR button

When you press this button (use a small-tipped object such as a ballpoint

pen), the mark will appear at the display. And the room temperature is

detected by the sensor which is built into the indoor unit and the air

conditioner is controlled accordingly.

If the remote control is located near a heat source, such as a space heater or

in direct sunlight, press the SENSOR button to switch to the sensor on the

indoor unit.

NOTE

LED CLEAN button

: If this button is pressed during AUTO, HEAT, DRY, COOL or

FAN operation, the UV anti-bacterial unit is activated for

one hour and cleans the air blown from the air conditioner.

ADDRESS switch

• The address switch changes to prevent mixing of signals from remote

control units when two air conditioners are installed next to each other.

Normally, the address switch is set to A. For more information, please

contact the dealer where you made the purchase.

• Normally, the tabs on the remote control unit should not be bent.

Temperature display selector button

This switches the temperature display

between °C and °F.

QUIET button

: When you press this button, the fan rotates slower than the

fan speed setting to provide a quieter operating sound.

ON TIME/OFF TIME setting buttons

Advance button

Return button

No display: The timer does not operate.

: The air conditioner starts at the set time.

: The air conditioner stops at the set time.

: The air conditioner stops and starts, or starts and

stops, at the set times every day. For details, see

“SETTING THE TIMER”.

OI-002-6-EG

2column_01_SAP-KRV96EH_EN.fm Page 6 Wednesday, July 18, 2007 5:32 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo SAP-KRV96EH Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info