Bedienungsanleitung Sanyo XS1822 (Seite 10 von 24) (Englisch)

481753

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

OI-201-10EG

Remote Control Unit (continued)

Program button For details, see “Setting the Timer”.

Press this button to select the mode you want to program.

TIMER SELECT button No display : The timer does not operate.

: The air conditioner stops at the set time.

: The air conditioner starts at the set time.

: The air conditioner stops and starts, or starts and stops, at the

set times every day.

MODE selector button Use this button to select the COOL or FAN mode.

(COOL)

: The air conditioner makes the room cooler.

(FAN) : The air conditioner works only as a circulation fan.

FLAP button Press this button to select the sweep function, which moves the flap up and

down automatically.

: The flap moves up and down automatically.

FAN SPEED selector button

: The air conditioner automatically decides the fan speeds.

: High fan speed

: Medium fan speed

: Low fan speed

1 HR. TIMER button : When you press this button, regardless of whether the unit is

(1-HOUR OFF TIMER) operating or stopping, the unit operates for one hour and then

shuts down.

ACL button (ALL CLEAR) Puts the remote control unit into pre-operation status. Always press this

button after replacing the batteries.

ADDRESS switch

•

Change the address switch to prevent mixing of signals from remote control

units when two Sanyo air conditioners are installed next to each other.

Normally, the remote control address switch is set to A. For the second

indoor unit, both addresses of the remote control unit and the indoor unit

must be changed. The second remote control unit address must be changed

to B by breaking off the tab ”A“. And the second indoor unit address must

be changed from 1-OFF, 2-OFF to 1-ON, 2-ON by switching the dip switch in

the indoor unit. For more information, please contact the dealer where you

made the purchase.

•

Normally, the tabs on the remote control unit should not be bent.

SENSOR button When you press this button (use a small-tipped object such as a ballpoint

pen), the mark will appear at the display. And the room temperature is

detected by the sensor which is built into the indoor unit and the air

conditioner is controlled accordingly.

NOTE If the remote control is located near a heat source, such as a space heater or

in direct sunlight, press the SENSOR button to switch to the sensor on the

indoor unit.

NOTE The remote control unit sends the temperature signal to the air conditioner regularly at five minute intervals.

If the signal from the remote control unit stops for more than ten minutes due to the loss of the remote

control unit or other trouble, the air conditioner will switch to the temperature sensor which is built into

the indoor unit and control the room temperature. In these cases, the temperature around the remote

control unit may differ from the temperature detected at the air conditioner’s position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sanyo XS1822 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info