Bedienungsanleitung Satel ACX-210 (Seite 5 von 5) (Englisch)

699609

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

SATEL ACX-210 3

 precision pliers,

 double-sided mounting tape.

1. Connect the temporary power supply (4...24 V DC) to the expander.

2. Add the expander to the wireless system (see the ABAX 2 / ABAX controller manual or

the INTEGRA 128-WRL control panel installer manual). The sticker with serial number

which shall be entered when registering the expander in the system can be found on the

device enclosure.

In the INTEGRA / VERSA alarm system, the expander is identified as ACX-200.

Simultaneous operation of the expander by the ABAX 2 and ABAX controller /

INTEGRA 128-WRL alarm control panel is not possible.

3. If the expander is to be installed in the enclosure of another device (e.g. a detector), put

the expander into that enclosure.

4. Place the expander / device in the enclosure of which the expander is mounted at the

location where it is to be installed.

5. Check the level of signal received from the expander by the ABAX 2 / ABAX controller or

the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select

another place for installation. Sometimes, it is sufficient to shift the device ten or twenty

centimeters to obtain a considerable improvement in the signal quality. You can also try

to turn the expander around to check what effect the change in antenna position will have

on the signal strength level.

The ARF-200 tester makes it possible to check the radio signal strength at the place of

future installation without having to put the expander there.

6. Disconnect the temporary power supply.

7. If the expander is to be mounted inside another device enclosure, run a bunch of wires

into the enclosure so as to make connections referred to in steps 8 to 10.

8. Connect detectors to the expander zones. For the EOL configuration, use a 2.2 k

resistor, and for the 2EOL configuration – two 1.1 k resistors.

9. Connect the devices to the expander outputs.

Given the specific character of radio communication, it is not recommended that the

expander be used in applications where quick switchover of the output status is

expected.

10. Connect the power leads to the +12V and COM terminals (use flexible conductors with a

cross-section of 0.5-0.75 mm

Do not use the battery to power the expander.

11. Fasten the expander to the mounting surface or, if it is to be installed in the enclosure of

another device, put the expander inside that enclosure. To install the expander, you can

use a double-sided mounting tape.

12. Power up the expander.

13. Configure the expander settings (refer to ABAX 2 / ABAX controller manual or INTEGRA

/ VERSA series control panels programming manual).

Taking into account the requirements of EN50131-3 standard, enter 400 ms when

configuring the sensitivity of alarm zones.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel ACX-210 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel ACX-210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info