Bedienungsanleitung Satel ARF-100 (Seite 3 von 4) (Englisch)

699870

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

SATEL ARF-100 3

– press the button to toggle between simulation of the device powered from an

external source and simulation of the device powered from a battery. After switch-

on the tester simulates operation of the device powered from an external source.

Which power supply method is being simulated is indicated by the LED .

Press and hold down the button to change the refresh rate of the radio signal level

indicator . After switching the tester on, the indicator refresh takes place during

polling and is signaled by one short beep. If you hold down the button longer than

3 seconds, the tester will enter and remain in the dense polling mode until the

button is released. When in this mode, the indicator is refreshed every 2 seconds,

which is signaled by two short beeps.

radio signal level indicator. The indicator consists of 7 LEDs (2 yellow and 5 green ones),

which present percentage of the radio signal level (15 – 100%). Intensity of the LED

lighting depends on which device is simulated by the tester. If a battery-powered device

is being simulated, the LED light is weaker. If, when the LEDs are ON, you change the

power supply method (by pressing the button), the LEDs will go off. They will only go

on again during the next polling and will show an updated radio signal level. If the tester

battery is low, all the indicator LEDs are blinking.

red LED indicating the tester operating mode:

ON – checking the level of radio signal received by the tester from the ABAX

controller / control panel,

flashing – checking the level of radio signal received by the ABAX controller / control

panel from the tester.

red LED indicating how the device being simulated is power supplied:

ON – powered from battery (e.g. AMD-100, AMD-101 and APD-100 detectors,

ASP-205 siren),

OFF – powered from an external source (e.g. ACX-200 expander, ASP-105 siren,

ASW-100 wireless controller).

4. Start-up and testing the radio signal level

There is a danger of battery explosion when using a different battery than

recommended by the manufacturer, or handling the battery improperly.

Be particularly careful during installation and replacement of the battery. The

manufacturer is not liable for the consequences of incorrect installation of the

battery.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

1. Install the battery and switch the tester on.

2. Add the tester to the wireless system (see the manual for ACU-120 / ACU-270 controller

or the installer manual for INTEGRA 128-WRL / VERSA / VERSA Plus / VERSA IP

control panel). The serial number of each tester is 0000500.

3. Use the button to define how the device simulated by the tester is supplied.

4. Start the test mode on the ABAX controller / control panel.

5. Place the tester in the location intended for installation of wireless device and check the

level of radio signal received by the tester from the ABAX controller / control panel and

the level of signal received by the ABAX controller / control panel from the tester. If the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel ARF-100 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel ARF-100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info