Bedienungsanleitung Satel ASD-200 (Seite 7 von 9) (Englisch)

699764

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

SATEL ASD-200 5

Be particularly careful during installation and replacement of the battery. The

manufacturer is not liable for the consequences of incorrect installation of the

battery.

1. Remove the plastic dust cap.

2. Turn the cover counter-clockwise (Fig. 5) and remove it (Fig. 6).

3. Install the battery.

4. Add the detector to the wireless system (see the ABAX 2 / ABAX controller manual or the

INTEGRA 128-WRL control panel installer manual). The sticker with serial number which

shall be entered when registering the detector in the system can be found on the

enclosure base.

In the INTEGRA / VERSA alarm system, the detector is identified as ASD-110.

Simultaneous operation of the detector by the ABAX 2 and ABAX controller /

INTEGRA 128-WRL alarm control panel is not possible.

5. Replace the cover.

6. Put the detector at the place of its future installation.

7. Check the level of signal received from the detector by the ABAX 2 / ABAX controller or

the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select another

place for installation. Sometimes, it is sufficient to shift the device ten or twenty

centimeters to obtain a considerable improvement in the signal quality. You can also try to

turn the enclosure to check what effect the change of antenna position will have on the

signal strength.

The ARF-200 tester makes it possible to check the radio signal strength at the place of

future installation without having to put the detector there.

8. Remove the detector cover.

9. Use wall plugs (anchors) and screws to secure the enclosure base to the ceiling. The wall

plugs (anchors) delivered with the device are intended for concrete, brick, etc. For other

types of surface (drywall, styrofoam), use the appropriately selected wall plugs.

10. Replace the detector cover.

11. Press the test / reset button (Fig. 1). Fire alarm should be triggered.

12. If in the premises where the detector is installed, any work is being carried out that may

lead to soiling of the optical chamber, put a plastic dust cover on the detector and leave it

there until the work is finished.

5 Maintenance

The detector should be subjected to regular checks for correct functioning. The periodic

checks should be carried out at least every 6 months. To check whether the detector is

operating properly, press the test / reset button (Fig. 1). This should trigger a fire alarm.

6 Cleaning the optical chamber

It is recommended that you have the optical chamber cleaned at least once a year. Cleaning

the chamber is necessary when the LED indicates fouling of the chamber (2 short flashes

during periodical communication with controller / control panel).

1. Start the service mode in the control panel (if the controller is connected to a SATEL

alarm control panel).

2. Turn the cover counter-clockwise (Fig. 5) and remove it (Fig. 6).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel ASD-200 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel ASD-200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info