Bedienungsanleitung Satel CA-10 (Seite 21 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 19

Setting keypad addresses

The address is keypad's additional tamper protection. A different (arbitrary) address

should be set in each keypad. To set an address in LED keypad, put jumpers on

corresponding pairs of the ABCD pins (see figures: 3, 4 and description of the service

function FS111). In LCD keypad, the address must be programmed. The programming

consists in entering four digits in binary code (by analogy with the LED keypads: 1=pins

shorted, 0=pins open). The control panel does not support LED keypads in which either all

jumpers or no jumpers are set, as well as LCD keypads in which the address 0000 or 1111

has been programmed. The address is stored in the panel EEPROM (non-volatile) memory,

together with the other system parameters.

The LCD-keypad address can be changed in two ways:

1. Directly (skipping the service code):

• Disconnect the keypad power supply and the data bus wires (CLK, DATA).

• Short-circuit the CLK and DATA terminals of the keypad.

• Switch on the keypad power supply. The following text will be displayed: „Keypad

hardware address: 1001” (the default value, corresponding to the jumpers read out in

the ABCD sequence).

• Using the [0] and [1] keys, enter the proper address and then press the [#] key.

The „Address set” text will be displayed on the keypad.

• Connect the keypad to the control panel in appropriate way (CLK, DATA).

2. By means of the keypad service functions:

• Activate the control panel service mode.

• Select in turn the items in menu of displayed functions: LCD keypad; Settings;

Keypad address.

• Using the [0] and [1] keys, enter the proper address and then press the [#] key.

The keypad will display the text: „Set addresses (FS124) ? 1=Yes”.

• Press the [1] key to automatically perform the FS124 service function and save the

settings.

Note: For correct handling of the LCD keypads by the CA-10 control panel, the FS124

function must be performed on each of the LCD keypads connected to the panel.

It may turn out on starting the control panel that the keypad is not supported (no reaction to

pressing the keys). A message appears then on the LCD keypad display that there is no

communication with the control panel. This is usually because the keypad address is different

than the one programmed in the panel. Depending on whether other keypads are also

connected to the panel, or this keypad is the only one in the system, you can follow either of

the two ways:

3. Call the service mode in another keypad and start the FS124 service function, which will

result in correct keypad addresses being automatically read out by the control panel.

In this case, remember to start the FS124 service function in all LCD keypads connected

to the panel.

4. Enter the service mode by means of jumpers and program a correct keypad address in the

control panel (see: Starting the Control Panel).

Connection of zone expander

In order to increase the number of zones, a zone expander can be connected, instead of

a full set of keypads. It makes available the zones of keypads required for full configuration.

The expander should be connected as a next keypad. It can be used in combination with

a different number of keypads. For details regarding the connection see the expander

installation manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info