Bedienungsanleitung Satel CA-10 (Seite 6 von 11) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

4 CA-10 SATEL

bypass zones, etc.). The installer may allow several partitions being operated with a single

keypad. To switch the keypad over to handle another partition, press and hold down the key

corresponding to the number of that partition (1, 2, 3 or 4). For the LCD keypad which has

been switched over to handle another partition, it is possible to switch it over again to handle

still another one. For the LED keypad, you can only press and hold down the key to go

back to operate the partition the keypad is assigned to. Irrespective of the keypad type, you

will be automatically brought back to the partition to which the keypad is assigned after 15

seconds of idle time.

4. Partition arming

A partition can only be armed from the keypad assigned to the partition or switched over to

handle it (see: OPERATING SEVERAL PARTITIONS WITH A KEYPAD).

Prior to arming, make sure that there are no violated zones (e.g. open windows or doors),

which may prevent the system from arming (if the system has been so configured by the

installer).

After arming, the exit delay countdown may be running, which allows you to leave the

premises without triggering alarm (the zones will be armed only when the exit delay

countdown is finished).

If, during the exit delay countdown, the control panel will not register leaving the premises

(the zone monitoring the exit route will not be violated), the selected zones can be

automatically bypassed, thus enabling you to stay in the protected premises. The installer

shall define which zones are to be bypassed in such a case.

4.1 Full arming

Enter the code and confirm using # key.

Note: The user having the authority 7 can only activate partial armed mode (the installer

selected zones will be bypassed).

4.2 Quick arming

If your installer has enabled the Quick Arm feature, you will be able to arm the system without

using the code. To quickly arm the system, press in turn the 0# keys.

4.3 Arming in silent mode

During the silent armed mode, the alarms from zones are only signaled on the keypad

(however, the installer can program the control panel output so that it can provide information

about alarms being signaled on the keypad). After activating the silent armed mode, the

installer selected zones will be bypassed.

1. Enter the code and confirm using key.

2. Press the 5 key (to start the ARMING SILENT user function).

5. Disarming and alarm clearing

The partition can be disarmed and the alarm cleared only from the keypad assigned to that

partition or switched over to handle it (see: O

PERATING SEVERAL PARTITIONS WITH A KEYPAD).

Alarms triggered from the keypad can be cleared from any keypad.

In order to disarm the partition and clear the alarm, enter the code and confirm with the # key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info