Bedienungsanleitung Satel CA-10 (Seite 12 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

10 Programming SATEL

Programming the service functions by means of keypad

In the LED keypads, the parameters being programmed are indicated with LEDs. In the LCD

keypads, the parameters being programmed are shown on the display. The way of

programming and data display in the keypad depend on the type of data entered with the

service function. The panel programming is based on three types of functions: bit (BIT), decimal

(DEC) and hexadecimal (HEX). The bit functions are used to program two-state parameters:

YES and NO (e.g. the functions of zone assignment to partition, options). The decimal functions

are used for programming data in the form of a few digits (for example, the test transmission

time - 4 digits, individual entry delay time of zones - 16 x 2 digits). The hexadecimal functions

are used to program hexadecimal data (e.g., monitoring codes).

BIT functions in the LED keypads

During programming with a bit function, the LEDs 1 to 8 show the current setting of particular

parameters (diode on - YES, off - NO). Pressing one of the keys [1] to [8] changes the state of

the corresponding diode. Having programmed 8 options, save them in the control panel using

the [#] key. If the programming function includes more parameters, the control panel will signal

with two short beeps acceptance of the first eight parameters, then it will go to the next set of

options, displaying their status on the LEDs 1 to 8. By means of the LEDs 9 to 12, the panel will

show which set of options is currently being programmed. When all the parameters have been

programmed, the control panel will signal exiting the function with four short a one long beeps.

The [

] key makes it possible to quit the function at any time without saving the changes in

currently displayed data.

BIT functions in the LCD keypads

After a bit function is called, the keys W X will change the cursor position and the keys ST will

the value of the bit at the cursor position. It is also possible to enter the desired bit number with

the numeric keys. Bit numbers 10-16 are entered by pressing [

] followed by the key with the

second digit. The combination of [

] and [#] terminates the function.

BIT functions with a list in the LCD keypads

After a bit function with a list is called in the first line of the display the function name will be

shown, while in the second line – the name of the first option in this function (e.g. System

options). The character indicates that the option is on. To change the switch state press any

numeric key. The keys ST will scroll the switch list. The [

] key makes it possible to quit the

function at any time without saving the changes.

DEC functions in the LED keypads

During programming with a decimal function the LEDs 1-4 show binary the first digit, LEDs 5-8 -

the second digit, while the LEDs 9-12 display binary the counter of digit pairs (see figure 1).

The programming consists in entering a two-digit number and confirming it with the [#] key.

Make sure that the entered data are correct, because the control panel does not verify

the input parameters and programming any wrong settings may result in malfunction of

the panel. The control panel will confirm acceptance of the data with two short beeps. When all

the parameters have been programmed, the function is exited which is signaled with four short

and one long beeps.

The [

] key makes it possible to quit the function at any time without saving the changes in

currently displayed data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info