Bedienungsanleitung Satel CA-10 (Seite 16 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

14 Programming SATEL

In the LED keypad programming of this code consists in entering three pairs of hexadecimal

characters (digits from 0 to 9 and characters A, B, C, D, E, F - see the table of codes). The

LEDs will first display previous settings, and, after the change - the values of characters

entered (binary, the first character - LEDs 1 to 4, the second - LEDs 5 to 8, number of pair of

programmed characters - LEDs 9-12). When the last pair of characters has been entered

and acknowledged, the control panel will automatically quit the function.

EXAMPLE (for the LED keypad):

programming the identifier 23C4D5

[2] [#] - call the required function.

[2][3] [#] - enter the two first characters

[

2][4] [#] - enter the two next characters

[

3][5] [#] - enter the two last characters; after acknowledging them the panel will automatically exit the

function

FS4 - programming computer telephone number (HEX)

The computer telephone number is necessary so that the control panel can call the

computer. If the computer telephone number is not programmed, the computer

initiated communication can be established in a simplified way - the control panel will

not hang up and call back.

The length of a telephone number can be up to sixteen digits and special characters. The

special characters are used to control the dialing process. In the LED keypad it is

programmed by entering the consecutive digits and characters in pairs. Each pair is to be

confirmed by the [#] key (see the example below). The LEDs 9-12 show (in binary form)

which pair of characters is being programmed, and the LEDs 1-4 and 5-8 show (also in

binary form) the values of programmed digits.

EXAMPLE: programming the number 0 - 556 40 31 (0D 55 64 03 1AA)

[4] [#] - call the required function

[0][

3] [#] - enter the two first characters

[5][5] [#] - enter the two next characters

[6][4] [#] - enter the two next characters

[0][3] [#] - enter the two next characters

[1][

0] [#] - enter the next character and the part of special code AA (telephone number end)

[

0] [#] - enter the second part of special code AA (telephone number end)

[

] [#] - exit the function after entering 11 characters.

The following codes has been assigned to the functions mentioned below:

HEX

) - control character (combination [

][0])

HEX

) - switch to pulse dialing (combination [

][1])

HEX

) - switch to tone dialing (combination [

][2])

HEX

) - wait for dialing tone (combination [

][3])

HEX

) - short pause (3 seconds) (combination [

][4])

HEX

) - long pause (10 seconds) (combination [

][5])

(

HEX

) - signal

in DTMF system (combination A[0])

HEX

) - signal # in DTMF system (combination A[1])

HEX

) - signal a in DTMF system (combination A[2])

HEX

) - signal b in DTMF system (combination A[3])

HEX

) - signal c in DTMF system (combination A[4])

HEX

) - signal d in DTMF system (combination A[5])

Notes:

• Do not program the control characters B, C and D before the telephone number (these

are set in the FS5 options).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info