Bedienungsanleitung Satel CA-10 (Seite 24 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

22 Programming SATEL

EXAMPLE:

LEDs: 1,3,6,8 are on, which gives value = 165:

State of the LEDs from 1 to 8 :  

VALUE

: 128+32 + 4+1 = 165

REACTION TIME

(ms):

PROGRAMMED VALUE

(165)

2640

In the LCD keypad, the time is programmed directly in milliseconds from 16 to 4080 (the

value is automatically rounded up to the multiple of the number 16).

By default, all the zones have the same reaction time (480 ms). In most cases, no change of

the time setting will be required.

The function is intended for advanced installers. It allows the zone sensitivity to be selected

where special detectors are used (for example, mechanical detectors of broken glass, or low

hysteresis detectors, not fitted with monovibrator at the output).

Note: The minimum sensitivity of the keypad zones and expander zones is 64 ms

(4 x 16 ms). The actual sensitivity values of these zones can amount to n x 64 ms

(n=1,2,3,...). This results from the way the keypad is handled by the control panel –

the status of these zones is read out at intervals of exactly 64 ms.

FS25 - programming zone type (DEC)

Selection of the zone type depends on the type of detector, as well as configuration of its

connection to the control panel. The following types of detectors and configuration are

possible: NC, NO, EOL, 2EOL/NC, 2EOL/NO. Determination of the type of detector and

configuration is necessary, since interpretation of information received by the control panel

will depend on it. For example, an open zone can mean correct state of the NO detector or

violation of the NC (or EOL) detector, as well as tamper violation in the case of 2EOL

configuration.

Programming in the LED keypad consists in entering the suitable two-digit number (to

determine the detector type and configuration) for the particular zones. Having confirmed the

detector type and configuration for one zone, the control panel proceeds to programming the

next type of zone, until particular detector types and configuration are assigned to all 16

zones. The following numbers are correct:

00 - no detector (for not used zones)

01 - NC detector (normally closed)

02 - NO detector (normally open)

03 - EOL detector (End Of Line Resistors - default value)

04 - 2EOL/NC detector (Double End Of Line Resistors – NC detector)

05 - 2EOL/NO detector (Double End Of Line Resistors – NO detector)

During the programming, the control panel will display the current parameter setting (in

binary form) on the LEDs 1 to 8. The LEDs 9 to 12 indicate the zone for which the detector

type is being programmed. (for zones 1-15 binary – see: Table of character coding for LED

keypads; for zone 16 LEDs 9-12 are off)

EXAMPLE:

programming the EOL type zones 1 do 6, NC type zones 7 to 8, the other zones (13 to 16)

not used

[2][5] [#] - call the function

[0][3] [#] - detector type for the first zone (LEDs 9-12 = 0001)

[0][3] [#] - detector type for the second zone (LEDs 9-12 = 0010)

[0][3] [#] - detector type for the third zone (LEDs 9-12 = 0011)

[0][3] [#] - detector type for the fourth zone (LEDs 9-12 = 0100)

[0][3] [#] - detector type for the fifth zone (LEDs 9-12 = 0101)

[0][3] [#] - detector type for the sixth zone (LEDs 9-12 = 0110)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info