Bedienungsanleitung Satel CA-10 (Seite 27 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

SATEL CA-10 25

[2][8] [#] - call the function

[#] - skip programming entry delay for zone 1

[#] - skip programming entry delay for zone 2

[#] - skip programming entry delay for zone 3

[3][0] [#] - program the entry delay for zone 4

[#] - skip programming entry delay for zone 5

[#] - skip programming entry delay for zone 6

[4][5] [#] - program the entry delay for zone 7

[6][0] [#] - program the entry delay for zone 8

[

] - exit the function - omit programming entry delay for the other zones

FS29 - programming maximum zone violation times

The FS29 function defines the boundary value of zone violation time which cannot be

exceeded, unless the zone detector is faulty. Information on the trouble is recorded in the

control panel event log and sent to the monitoring station. It can also be signaled on the

output selected for ZONE TROUBLE.

The programming procedure is similar to that in the FS24 function (programming the zone

sensitivity).

The violation time is set within the range of 0 to 255 seconds. When time 0 has been

programmed, the function is inactive.

EXAMPLE: (for LED keypad)

programming the maximum violation time for the zones 2 (60 seconds) and 4 (180 seconds)

[2][9] [#] - call the function

[0] [#] - disable the trouble check for the zone 1 (by default, the trouble check for all zones is

disabled, so you can skip the zones for which this parameter is not programmed, by

pressing the [#] key)

[6][0] [#] - set the time for the zone 2

[#] - skip programming the zone 3

[1][8][0] [#] - set the time for the zone 4

[

] - quit the function - skip time programming for the other zones.

Note: The violation time is only checked for the "alarm zones" (reaction type from 00 to 11).

FS30 - programming the zone no violation time

This function defines the time after which the absence of a given zone violation will be

recognized by the panel as a trouble condition (e.g. a faulty or obstructed detector). The time

of no violation is only counted when the zone is disarmed.

Information on the zone trouble is saved in the event log, and can be sent to the monitoring

station and to the output selected for ZONE TROUBLE.

This parameter can be defined individually for each zone in the same way as in the FS29,

within the range of 0 to 255 hours. Having programmed 0 means that the zone no violation

time monitoring is disabled.

Note: The no violation time is only checked for the "alarm zones" (reaction type from 00 to

11).

Functions programming output parameters

FS31 - programming OUT1 output

The function makes it possible to define basic parameters regarding the OUT1 output:

• output type (determines in which conditions the output will be activated),

• output operation time,

• operation options (e.g., "polarity").

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info