Bedienungsanleitung Satel CA-10 (Seite 30 von 60) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

28 Programming SATEL

of the LEDs 1 to 8. The setting completed, confirmation of the options with the key [#] will

exit the function.

EXAMPLE:

programming the OUT1 output for the BURGLARY/FIRE ALARM type operation, for 5

minutes, with polarity 0V in active state

[3][1] [#] - call the function. The LEDs 1-8 will show number of current output type (LEDs 1-4 will show

binary first digit, LEDs 5-8 second digit). The blinking LED 12 signals the output type being

programmed.

[0][2] [#] - enter and confirm the output number (the LED 12 starts blinking - operation time

programming)

[0][5] [#] - program and confirm the time (LEDs 11 and 12 start blinking - proceed to programming the

output option)

[6] - LED 6 goes on - the „time in minutes” option is activated

[8] [#] - LED 8 goes off - set the "polarity" = 0V and exit the function.

In the LCD keypads, after selecting the function of output OUT1 programming, the menu will

be displayed, which enables the output parameters to be set. Movement through the menu is

possible by means of the arrow keys ▲ and ▼. The first parameter, i.e. the output function,

is selected by means of the arrow keys ◄ and ►, or by entering the two-digit function

number (DEC). The second parameter, i.e. the output operation time, is determined by

entering a two-digit number from 00 to 99 (DEC). Remember that, when setting options at

the next stage of programming, you should define, whether the operation time was indicated

in seconds or in minutes. The third parameter, i.e. the output options, is programmed by

scrolling through the option list with the arrow keys ◄ and ► and toggling their status by

means of any numeric key, which is indicated on the display by appearance/disappearance

of the flag at the given option. The setting completed, confirmation of the parameters with

the key [#] will exit the function.

FS32 - programming list of zones OUT1 (BIT)

The function is used to program the output controlling zones. The selection of zones limits

the output operation only to reaction to violation of those zones.

The zone selection should only be used when it is necessary to have separate

signaling for events from a specific zone or a group of zones.

If no list of zones is indicated, the control panel will assume by default that the output reacts

to events from any zone – for example, the BURGLARY alarm type output will signal alarms

for each alarm zone in the control panel. Of course, the zone reaction type is taken into

consideration, e.g. the alarm signaling output will not react to a change of state of the arming

zone.

Programming the list of zones makes the control panel to skip the programmed

selection of zones when defining which zones are to activate the output.

For the outputs reacting to keypad events, the list of partitions is taken into consideration,

while the list of zones is irrelevant (e.g. the 3 wrong codes alarm signaling).

The programming procedure is identical as in the functions FS8 – FS11.

FS33 - programming OUT2 output

The function defines the basic parameters associated with the OUT2 output. The

programming procedure is same as for the FS31.

FS34 - programming list of zones OUT2 (BIT)

The function programs the list of zones associated with the OUT2 output. The programming

procedure is same as for the FS32.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info