Bedienungsanleitung Satel CA-5 Plus (Seite 6 von 27) (Englisch)

699583

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Installer Manual CA-5

1 –

BURGLARY ALARM

(with the operating time equal to zero, the output is active until

clearing the alarm, e.g. visual indication)

2 –

KEYPAD ALARM

3 – READY

STATUS

(active when none of the zones is violated)

4 –

ARMED STATUS

5 –

INDICATOR OF

AC,

BATTERY OR TELEPHONE LINE TROUBLE

6 – AC

LOSS INDICATOR

7 –

BATTERY TROUBLE INDICATOR

8 –

TELEPHONE LINE TROUBLE INDICATOR

9 – GROUND

START

SIGNAL

(the signal of 2-second duration which occurs before "lifting

the handset" by the control panel and which is required by a specific type of

telephone exchange)

10 –

TELEPHONE LINE RELAY

(description see p. 17)

11 – MONO

SWITCH

(control type, activated for a specified time period with the user

function 7)

12 – BI

SWITCH

(control type, switched over permanently with the user function 8)

13 – RESETTABLE

POWER

(deactivated with the user function 9 for a time period

programmed as the output cutoff time – minimum 4 seconds)

14 – DURESS

ALARM

(signals disarming or alarm clearing with the use of a "duress" code)

15 –

MONITORING ACKNOWLEDGEMENT

(activated by the control panel for 3 seconds after

correctly ending communication with the monitoring station)

16 –

PARTIALLY ARM STATUS

(active when the armed mode is on with zones bypassed)

The number of output function corresponds to the number programmable in the FS 48 and

FS 50 service functions to determine the output function.

The OUT2 and OUT3 outputs in the active state will short-circuit the terminal to ground.

It is possible to alter the way of work of outputs. You can change polarization of the terminals

-OUT1, as well as OUT2 and OUT3 (FS 84 options 1, 2 and 3). By selecting the „Polarization

OUTn reversed” option (n – output number), the terminal will be shortened to the common in

its inactive state and cut off in the active state.

The following parameters can be programmed for the outputs:

− alarm signaling time (FS 47)/cutoff time of FS 49 and FS 51 outputs,

− burglary alarm signaling delay (FS 46, FS 82 and FS 83).

The output OUT1 is designed to signal the burglary and fire alarms. The installer can select

the identical signaling mode for the fire alarm and for the burglary alarm (FS 84 option 4),

however, the signaling delay (if any) will only apply to the burglary alarm.

The installer can activate the signaling of arming/disarming and alarm clearing on the OUT1

output (FS 84 option 5).

The power supply outputs for the detectors (AUX) and keypad (KPD) have a common

polymer fuse, limiting the current consumption from the power supply by the external devices

to 350 mA.

All the outputs are protected against inductive loads and impulse interference.

3.3 LED

KEYPAD

In the LED keypad basic information concerning the system status is provided by means of

light emitting diodes LED (for detailed description, see the user manual). Displayed are the

status of zones and system (supervision, alarm), information on power supply status,

detection of emergency situation and operation in programming mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Plus Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info