Bedienungsanleitung Satel CA-5 Plus (Seite 20 von 27) (Englisch)

699583

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Installer Manual CA-5

The function works in the following way:

• The control panel dials the first number of the monitoring station in order to send the

event code. If it fails to send the code, the other number of the station is dialed.

• If connection to the second number fails, the control panel switches over the telephone

line and dials again the first number of the station. When the problem recurs, the control

panel redials the second number.

• If the code is still not received by the station, the control panel returns to the first

telephone line (deactivates the type 10 output) and repeats the whole cycle of dialing

the station numbers.

5. STARTING THE CONTROL PANEL

After all electrical connections are made and their correctness checked, you can proceed to

start the system. It is recommended to begin the work with the control panel with no sirens

connected. These can be connected after programming parameters is completed and

operation of the realized security system tested.

After the power is switched on, the keypad will report readiness for work with four short

beeps followed by a long one. If the panel starts alarming (the [

ALARM

] LED is on and the

keypad makes a continuous sound), it usually means that a tamper alarm has been triggered

by incompatibility of factory settings with parameters of the connected detectors. To clear the

alarm enter the MASTER access code [1][2][3][4] and press [#]. Then, enter the factory

service code [1][2][3][4][5] and accept it with the [#] key – the control panel will enter the

service mode. The [

PROGRAM

] LED will come on and will be lit up continuously and the

keypad will start emitting a short beep every 3 seconds. At this moment, you can proceed to

programming the control panel.

The list of service functions as well as the method of introducing and changing of

system parameters by means of the keypad have been described in a separate

instruction called S

ETTINGS

IST

If the service code is unknown (as its contents was previously changed), it is necessary to

carry out the procedure of entering the service mode „from the pins”. This procedure is

presented together with the description of service functions in the S

ETTINGS

IST

Note: Blinking of all LEDs and sound signals given at the same time by the keypad indicate

that there is a faulty connection (no communication with the control panel) – the cable

connections must be checked.

If the suggested procedure turns out to be unsuccessful, the option to enter the service mode

„from the pins” must have been disabled in the control panel by software means. If this is the

case, it is necessary to carry out another procedure which would unblock the control panel

and restore the factory settings - see description of the FS 9 service function in the S

ETTINGS

IST

After completing the procedure, exit the service mode using the FS 0 function and call the

service mode again – this time from the keypad – entering the factory access code

[1][2][3][4][5] and accepting it with the [#] key.

Re-entering the service mode by the control panel means that the equipment operation is

correct and programming of all necessary parameters may be commenced.

A trouble with entering the service mode by hardware method points to incorrect performance

of the above mentioned procedures.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Plus Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info