Bedienungsanleitung Satel CA-5 (Seite 5 von 27) (Englisch)

699607

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

CA-5 SATEL

3. CONTROL PANEL CHARACTERISTICS

3.1 Z

ONES

The CA-5 control panel has 5 zones, all of them on the mainboard. The control panel

accepts any detectors connected in the NC, NO, EOL, 2EOL/NC, and 2EOL/NO

configuration. The 2EOL configuration allows the control panel to simultaneously control the

detector and its tamper circuit while using one pair of wires.

The zones can serve the following functions in the system:

0 –

ENTRY

EXIT

(monitors entry to and exit from the facility by the user; having detected

entry into the facility, it actuates the mechanism of interior zone alarm delay)

1 –

INTERIOR DELAY

(if there is no entry into the facility, it works as the instant zone)

2 –

INSTANT

(triggers alarm instantly after violation when the control panel is armed)

3 –

COUNTING

(to 2 violations throughout the monitoring time as determined by the entry

delay – the second violation will trigger alarm)

4 – 24

H PANIC

(armed 24 hours; makes it possible to connect panic buttons)

5 – 24

H FIRE

(armed 24 hours; triggers the fire alarm)

6 – 24

H TAMPER

(armed 24 hours)

7 –

ARMING

DISARMING

ALARM CLEARING

(makes it possible to connect remote control set)

8 –

PERIMETER

(armed from starting the exit delay countdown)

9 –

ENTRY

EXIT FINAL

(having detected the end of violation of this zone, the alarm control

panel will end the exit delay countdown and enter the armed mode)

10 –

DELAYED

The number of zone function corresponds to the number programmable in the FS 26–30

service functions to determine the type of zone reaction.

The reaction time for each zone can be programmed from 0.016 s to 4.08 s (FS 16–20).

For the zones types 0, 1, 3, 9 and 10, individual delay times can be set (FS 31–35).

For each zones, it is possible to determine six codes of events to be sent to the monitoring

stations (FS 57, FS 58, FS 60, FS 61, FS 80 and FS 81).

The zones can be selectively bypassed with the user function 4, while bypassing of the 24h

zones is only possible by using the service code.

See also: S

ETTINGS LIST

, section „Zones”.

3.2 O

UTPUTS

The CA-5 is fitted with 3 signal outputs (OUT1, OUT2, OUT3) and 2 power supply outputs

(AUX and KPD).

The OUT1 output (high-current, 1.1 A polymer fuse) is a specialized alarm output. It is

intended for connecting an audible siren. This output has two terminals: +OUT1 and –OUT1.

Activation of the output is effected by shorting the -OUT1 terminal to the common (basic

output polarization).

The +OUT1 terminal serves the function of a power supply output with 1.1 A polymer fuse.

The control panel monitors the fuse condition and signals output overload.

The OUT1 output can be assigned to selected control panel zone (FS 41 – 45). The selection

applies also to other

BURGLARY ALARM

outputs.

The low-current OUT2 and OUT3 outputs (OC, up to 50 mA) are programmable and each

of them can serve one of the following functions:

0 –

NOT USED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info