Bedienungsanleitung Satel CA-5 (Seite 12 von 24) (Englisch)

699607

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

SER

ANUAL

CA-5

set are indicated by the number of a lit up LED, whereas troubles relating to the second set

are indicated by the number of an extinguished LED (one of five).

The previous (earlier) troubles are available for readout by consecutively pressing any key of

the keypad, except for the [

] key which cancels the trouble memory review function.

5.3 C

URRENT TROUBLE CHECK

OUT

[7]

When the control panel signals a trouble detection (the [TROUBLE] LED is blinking),

holding down the [7] key (until you hear a single beep) will activate the Current Trouble

Check-out Function. On activating the function, the [PROGRAM] LED will start blinking,

and the LEDs 1 to 5 will indicate any possible troubles from the first set (list of troubles as per

the table). Pressing any key (except for the [

] key) will change the set of displayed troubles

to the other one, which will be signaled by two short beeps. Consecutive pressing of any key

will display information, alternately, on the first set of troubles and on the second one.

Pressing the [

] key will quit the function.

The meaning of the LEDs is as follows:

LED No. FIRST SET OF TROUBLES

1 230V AC power supply loss

2 Battery trouble

3 OUT1 output trouble

4 Power supply outputs trouble

5 Clock loss

SECOND SET OF TROUBLES

1 No voltage on telephone line

2 Problem with access to settings memory

Wrong communication codes (connections from

computer blocked for 30 minutes by the panel)

4 Monitoring trouble

5 Dialing error

Note: During the trouble memory review, the extinguished LED No. 3 (a second set

trouble) means „Unsuccessful DWNL (downloading)”. The meaning described in the

table refers to the current trouble check-out only.

5.3.1 Description of some trouble signaling causes

230V AC power supply loss

- the control panel is fitted with a backup power supply to enable

a limited time operation without the mains supply; if the AC loss is indicated despite the electrical

installation being OK, you should call the service.

Battery trouble

– means that the battery voltage is too low (lower than 12V under load). This

condition may hold for several hours after AC supply loss (or after connecting a discharged

battery). The battery charging time depends on its capacitance (the battery is charged with direct

current of approx. 350mA, the time necessary for testing the battery status is about 12 minutes).

Overload OUT1 output

– overload (installation short-circuiting) – usually requires intervention of the

service personnel.

Overload power outputs

– information on the installation fault, requires intervention of the service

personnel (it can be only displayed during the trouble memory review).

Clock loss

– occurs on disconnecting the power supply and restarting the control panel; the clock and

date should be set with the user function 6.

No voltage on telephone line

– means cut-off of the telephone line; it may be also caused by

lifting the handset of the telephone connected to the same line for longer than the time specified by

the installer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-5 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info