Bedienungsanleitung Satel CA-6 (Seite 5 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CA-6 SATEL 3

The zones (input lines) can perform the following functions in the system:

00 – exit/entry – the violation of which, when in the armed mode, will start countdown of the entry

delay time and will enable the delay for INTERIOR DELAY type zones (violation of an

INTERIOR DELAY zone without prior violation of the ENTRY/EXIT zone will trigger an

alarm immediately). Upon violation, a “zone violation” code is sent to the report station

(it is possible to skip sending this message), and, after counting down the "entry delay

time" and triggering the alarm – a “zone alarm” code. The "entry delay" countdown can be

signaled in the keypad. It is possible to define automatically bypassing zones if no

ENTRY/EXIT zone is violated during the exit delay time. Because of its additional

functions, this zone type cannot be used as a common zone for both partitions.

01 – delayed – when violated in the armed mode, it starts delay countdown, after which an alarm is

triggered. It will not occur if the zone is disarmed before completion of the delay

countdown. Upon violation, a “zone violation” code is sent to the report station, after

counting down the entry delay time and triggering the alarm – a “zone alarm” code.

The delay is not signaled in the keypads.

02 – interior delayed – when violated in the armed mode after previous violation of the

ENTRY/EXIT zone, it behaves like a DELAY zone. When violated in the armed mode

without previous violation of the ENTRY/EXIT zone, it behaves like an INSTANT zone.

03 – instant – when violated in the armed mode, it immediately triggers an alarm and sends a ”zone

alarm” message to the monitoring station.

04 – day/night – when violated in the armed mode, it behaves like an INSTANT zone, while when

disarmed, it will signal violation in the keypad (unless function is disabled – FS20, second

set, option 3) and send a “zone violation” code to the station.

05 – counting L1 – when violated in the armed mode, it increases the status of the first of three

violation counters (a “zone violation” code is sent to the station), until the number of

violations specified for that counter is exceeded (programming in FS7). Then the violation

triggers an alarm (a ”zone alarm” code is sent to the report station). By default, the count-

up time is set at 30 seconds. It is possible to program another counter count-up time

(FS123). If the preset number of violations is not reached within this time, it will be reset.

The next zone violation will start the add-up procedure all over again. The violations are

added up starting from zero, and the count-up time starts upon the first violation after

resetting the counter. The "counting L1" function can be assigned to more than one zone,

in that case violations of those zones will be summed up. The zone will trigger an alarm

upon exceeding the programmed number of violations added up by a given counter.

Alarm can also be triggered after resetting the counting zone counter, if the zone

associated with the given counter is still violated.

06 – counting L2 – operation identical as for the "counting L1", but changes the status of the

second of the three counters.

07 – counting L3 – operation identical as for the "counting L1", but changes the status of the third

of the three counters.

08 – 24H audible – armed all the time, irrespective of whether the partition it is assigned to is

armed, or not. Each violation of this zone will trigger alarm on the “burglary alarm” type

outputs, in the keypad and will send a “zone alarm” code. It makes possible to create

tamper circuits and panic buttons.

09 – 24H auxiliary – armed all the time, irrespective of whether the partition it is assigned to is

armed, or not. Each violation of this zone will trigger an alarm in the keypad and will send

a “zone alarm” code. It is intended for connecting detectors such as gas or flood sensors,

etc.

10 – 24H silent – armed all the time, irrespective of whether the partition it is assigned to is armed,

or not. Violation of this zone will only send a “zone alarm” code to the monitoring station.

11 – 24H fire – armed all the time, irrespective of whether the partition it is assigned to is armed,

or not; intended for the fire detectors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info