Bedienungsanleitung Satel INT-TSG-BSB (Seite 22 von 28) (Englisch)

699393

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

20 INT-TSG SATEL

programmed for the R1 resistor (the value of one resistor must not be less than 500



). By

default, the following values are programmed:

R1 = 1,1 k



;

R2 = 1,1 k



The resistor value for Single EOL configuration is the sum of R1 and R2 resistors.

INTEGRA Plus

: parameters of the EOL resistors should be defined for the mainboard zones.

The same parameters will be set automatically for the zones in keypads in which the value

of EOL resistors is programmable. Therefore, the “EOL resistance value” tab is not

available.

7.2 Keypad connected to VERSA / VERSA Plus control panel

To configure the keypad settings, you can use:



LOAD

X program:



“Versa – Structure” window



“Hardware” tab



“Expanders” branch

[keypad name]

. The D

LOAD

X program alone makes it possible to configure all the

settings.



keypad:



ERVICE MODE



2. H

ARDWARE



1. K

PDS

EXPS



2. S

ETTINGS

[keypad

name].

How to enter the service mode, refer to the section on programming the keypad

address by means of the service function (p. 5).

7.2.1 Parameters and options

Shown in square brackets are the names displayed on keypads.

Name

– individual name of the keypad (up to 16 characters).

Tamper signaled in part.

[Tamper in p.] – partition where alarm will be triggered in the event

of keypad tamper (opening the enclosure or disconnecting the keypad from the bus).

CHIME signal of zones

[Zone chime] – the keypad can audibly signal violation of selected

zones. If the zone is armed, violation will not trigger the CHIME signal.

Date/Time format

– the way how date and time will be presented on the display.

Options

Sign. entry delay

[Entry time sign.] – if this option is enabled, the keypad will audibly signal

the entry delay countdown.

Sign. exit delay

[Exit time sign.] – if this option is enabled, the keypad will audibly signal the

exit delay countdown.

Sign. alarms

[Alarm signalling] – if this option is enabled, the keypad will signal the alarms

audibly.

Quick arming – Partition 1

[Part.1 QuickArm] – if this option is enabled, partition 1 can be

armed without entering the code.

Quick arming – Partition 2

[Part.2 QuickArm] – if this option is enabled, partition 2 can be

armed without entering the code.

Keys sound

– with this option enabled, pressing the keypad keys is confirmed by beeps.

Sign. trbl in part. arm

[Trbl.in part.arm] – if this option is enabled, the LED goes off after

both partitions are fully armed (if the option is disabled, the LED goes off after just one of

the partitions is armed in any mode).

Show code entering

[Code entry ind.] – if this option is enabled, entering the code is

presented on the keypad display by asterisks.

Chime on/off

– if this option is enabled, the chime signal can be turned on/off after tapping

and holding for 3 seconds

on terminal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel INT-TSG-BSB Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel INT-TSG-BSB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info