Bedienungsanleitung Satel INT-TSH-BSB (Seite 18 von 28) (Englisch)

699392

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

16 INT-TSH SATEL

Commands list – commands assigned to the currently highlighted macro command. The

and buttons allow you to change the order of commands (moving the selected

command up and down).

Add – click to add to the list a new command, selected in the “Command” field.

Change – click to save the changes to the command parameters which were made after

adding the command to the list (otherwise, the changes made will not be saved).

Delete – click to remove the highlighted command from the list.

Command – the control panel executed function which can be assigned to the macro

command. The list of all available functions will be displayed after you click the

button.

Depending on which function you choose:

Arming – select the partitions which are to be armed (double-click on the field designated

by the partition number) and define the arming mode (next clicks on the field designated

by the partition number; the digit inside the field has the following meaning: 0 - fully

armed; 1 – fully armed+bypasses; 2 – armed without interior; 3 - armed without interior

and without entry delay).

Disarming – select the partitions which are to be disarmed (double-click on the field

designated by the partition number).

Alarm clearing – select the partitions in which alarm is to be cleared (double-click on the

field designated by the partition number).

Bypass zones – select the zones which are to be inhibited (double-click on the field

designated by the zone number).

Unbypass zones – select the zones which are to be unbypassed (double-click on the field

designated by the zone number).

Outputs ON – select the outputs which are to be activated (double-click on the field

designated by the output number).

Outputs OFF – select the outputs which are to be deactivated (double-click on the field

designated by the output number).

Change outputs state – select the outputs whose status is to be changed (double-click

on the field designated by the output number).

KNX telegram – program the following parameters of KNX telegram for the INT-KNX

module:

INT-KNX module – INT-KNX module which is to send the telegram.

Group address – the group address which will be inserted in the telegram.

Type – the telegram type.

Value – the value that will be inserted in the telegram (parameter available for some

types of the telegram).

Priority – telegram priority (if two elements of the bus start transmitting simultaneously,

the telegram with higher priority will be sent first).

KNX telegram (v2) – program the following parameters related to setting the value of KNX

communication object:

Module INT-KNX – INT-KNX-2 module in which the value is to be set.

Makro Command – name of the VIRTUAL (MACRO) type object, defined in INT-KNX-2

module.

Data type – size and meaning of the communication object data defined in INT-KNX-2

module for selected object.

Value – value to be set (if the type of data provides for sending a sequence of

characters, you can enter up to 13 characters).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel INT-TSH-BSB Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel INT-TSH-BSB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info