Bedienungsanleitung Satel Integra 128 Plus (Seite 8 von 102) (Englisch)

699072

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

6 Programming SATEL

2.2 Starting the service mode “from pins”

When entering the service mode in the normal way is not possible (the control panel does not

support LCD keypads, does not accept the service code, etc.), you can use the emergency

procedure, so-called, starting “from pins”.

1. Turn off the control panel power supply (first disconnect the AC power, and then the

battery).

2. Put a jumper on the RESET pins located on the control panel mainboard.

3. Turn on the control panel power supply (first connect the battery and then the AC power).

The DIALER LED will start blinking.

4. Wait a few seconds until the DIALER LED goes out and remove the jumper from the pins.

The control panel will enter the service mode. The service mode menu will be displayed

on the LCD keypad with the lowest address.

The service mode will not start if:

− the computer with running DLOADX program is connected to the RS-232 port,

− the DISABLE SERVICE MODE option is enabled – in such a case a prompt will appear

on the display, whether you want to delete all the control panel data. Pressing the

key number 1 will restore the factory settings and then will start the service mode.

The service mode can be started “from pins” even if the installer does not have access

(the administrator has disabled the PERMANENT SERVICE ACCESS and has not

programmed the service access time). If this is the case, the installer can get access

to the MASTERS function by entering the service code, confirmed by pressing the

key,

within about 20 seconds after ending the service mode started “from pins”.

2.3 Hiding the service mode

The installer can hide the service mode using the HIDE SM NOW function (SM SETTINGS HIDE

SM NOW). The control panel will remain in the service mode, but the service mode menu will

not be displayed. This function can be useful, if e.g. the installer has to leave the keypad, but

does not want unauthorized persons to have access in the meantime to the service menu. To

get access to the service mode menu, you must proceed in the same way as when entering

the service mode.

The service mode can be hidden automatically after a specified period of time has elapsed

since the last operation was performed on the keypad (see description of the HIDE SERVICE

MODE AFTER

parameter p. 74).

2.4 Exiting the service mode

To exit the service mode you can use the SERVICE END function.

After exiting the service mode, the control panel verifies whether the data in RAM memory

have changed in relation to the data stored in non-volatile FLASH memory. When the data in

RAM have been changed, a prompt will be displayed asking whether the new settings are to

be saved to FLASH memory. Pressing the key with number 1 will save a copy of the settings

to FLASH memory. By saving a copy of the settings to the FLASH memory, the control panel

will be able to restore them from a backup copy if an error is detected in the data stored in

the RAM memory.

2.5 Service mode menu

Service end

SM settings

Service code

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Plus Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info