Bedienungsanleitung Satel Integra 128 Plus (Seite 85 von 102) (Englisch)

699072

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

SATEL INTEGRA Plus 83

For each user schedule, you can:

• program an individual name (up to 16 characters),

• indicate the timers which will determine when the user will have access to the system.

10. Reporting

The control panel can send event codes to the monitoring station using the following

transmission paths:

• analog telephone line,

• Ethernet (connection of the ETHM-1 Plus / ETHM-1 module to the control panel required),

• GPRS (INT-GSM module must be installed in the alarm system or SATEL GSM module

must be connected to the control panel),

• SMS (INT-GSM module is required to be installed in the alarm system) – the control panel

gets no acknowledgement of event code receipt.

The control panel will try to send event code to the monitoring station using in turn:

1. ETHM-1 Plus / ETHM-1 module and/or INT-GSM module. If several such modules are

connected to the control panel, that with the lowest address will be used. Event code can

be sent via Ethernet, GPRS or SMS.

When configuring the ETHM-1 Plus module to which the INT-GSM module is

connected, or when configuring the INT-GSM module connected directly to the control

panel, define priority of the transmission paths. The transmission path which is not

included in the list defining the priority of transmission paths, will not be used.

2. SATEL GSM module for GPRS transmission.

3. analog telephone line (basic and backup telephone number).

If the event code is successfully sent via one transmission path, the other transmission paths

will not be used.

If sending the event code via one transmission path fails, the control panel will try to send the

event code by using the next transmission path. In the case of reporting via the telephone

line, if the event cannot be sent despite completion of the preprogrammed number of retries,

the control panel will hang up until a next event occurs, or for a specified period of time. After

the time expires, the control panel will make further attempts to send the event.

The reporting parameters can be programmed:

• using the keypad, in the service mode, by means of the functions available in the

MONITORING submenu,

• using the DLOADX program, in the “Reporting” window.

For correct operation, the reporting function may require enabling some system options.

Reporting through the ETHM-1 Plus / ETHM-1 / INT-GSM / GSM modules requires that some

telephone options be enabled and settings of these modules properly configured.

Before you proceed to the programming, obtain from the monitoring station operator all data

necessary to correctly start the reporting function:

• depending on the method of sending events:

– telephone number of the monitoring station (telephone reporting),

– server address, port number, STATION KEY and KEY (ETHM) (reporting through Ethernet

network),

– server address, port number, STATION KEY and KEY (GPRS) (GPRS reporting),

– telephone number of the monitoring station and SMS message format (SMS reporting),

• transmission format required by the monitoring station,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Plus Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info