Bedienungsanleitung Satel integra 128-WRL (Seite 28 von 37) (Englisch)

699062

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

26 Installer Manual SATEL

Most of the ABAX 2 wireless devices are identified in the alarm system by the names

known from the ABAX system.

For some wireless devices, you can select whether the device will take up one or two

positions (channels) on the list of devices. If you select one position for the ABAX

device:

− AMD-101 – only additional NC input will be supported,

− AMD-102 – only additional inputs (roller shutter and NC) will be supported,

− AOD-200 – only the motion detector will be supported,

− ATD-100 – you will be able to program only one temperature threshold,

− AVD-100 – only the vibration detector will be supported.

LCD Keypad

You can add wireless devices in service mode, using the NEW DEVICE function (STRUCTURE

HARDWARE EXPANDERS SETTINGS ABAX - INTEGRA NEW DEVICE).

When adding a device you can select the alarm system zone to which you want to assign the

device. If the device takes up more than one position on the list of devices, additional zones

will be assigned to the device automatically (these will be the zones following the selected

one). To the outputs, the device is assigned automatically.

1. Start the NEW DEVICE function.

2. When the “Device serial number:” is displayed, enter the serial number of the device

being added.

3. Press .

4. When the “Open device tamper” command is displayed, power on the device (insert the

battery into the device, turn on the device power, etc.).

5. Type and serial number of the device will be displayed (if a message is displayed instead

to inform you that the entered serial number is invalid or the device is already registered,

press to quit the function).

6. Press the key 1.

7. If you can select whether the device will take up one or two positions (channels) on the list

of devices, a special message will inform you about it. Press the key 1 (the device will

occupy 1 position) or the key 2 (the device will occupy 2 positions).

8. Use the  and  keys to select the zone to which you want to assign the device.

9. Press .

10. A message will be displayed to inform you that expander identification procedure has

been started.

11. When the procedure is finished, the new name of the zone / output to which the device

has been assigned will be displayed. You can change that name.

12. Press .

13. If the device occupies two or more zones / outputs, the name giving procedure is

repeated for them.

DLOADX program

You can add wireless devices in the “Structure” window, “Hardware” tab, after clicking on the

“Wireless System”.

The device being added is assigned to zones and outputs automatically

1. Click on the “New device” button.

2. The “New device” window will open.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel integra 128-WRL Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel integra 128-WRL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info