Bedienungsanleitung Satel Integra 128 (Seite 71 von 114) (Englisch)

699073

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 69

2. Program the output 1, to which the siren is connected, as 47. OUTPUTS LOGICAL OR, and

select the outputs 63 and 64 as the controlling ones. The output 1 will be turned on, if the

output 63 or 64 is active.

3. Program the output 62, which does not exist physically, as 26. TIMER type. Program the

timer, which is to control the output, as a daily one, turned on at 16.00 and turned off at

8.00.

4. Program the output 2, to which the siren is connected, as 46. OUTPUTS LOGICAL AND, and

indicate the outputs 1 and 62 as the controlling outputs. As a result, the output 2 will

signal alarms and confirmation of partition arming/disarming, but only from 16:00 to 8:00.

Beyond these hours, the output will be inactive.

5.9 Output testing

Using the function available in the service mode menu in the keypad (OUTPUTS TEST),

you can test the outputs. After starting the function, the list of system outputs will be

displayed. Select the output to be tested and press the

or  key. The keypad will display

a submenu which enables the output testing. By using the or  key, you can

activate/deactivate the output. You can also deactivate the output by means of the numerical

keys. Press to quit the submenu and return to the list of system outputs.

The output under test will stop performing its previous function (if it was active, it will

be deactivated).

If there are wireless sirens in the system, starting the function of output testing will

unblock the signaling in them (the signaling is normally blocked for the service mode

duration). It should be remembered that the command to block/unblock the signaling is

sent out during polling. This will cause a delay whose duration depends on the

programmed response period.

When testing the control output for ASP-205 wireless siren, it should be remembered

that the signaling is only triggered during the polling.

6. System options

Most of the options and parameters described in this section can be programmed:

• using the keypad, in the service mode, by means of the functions available in the OPTIONS

submenu,

• using the DLOADX program, in the “Options” window.

Shown in square brackets are the names used in keypads.

6.1 Telephone options

Reporting - TELEPHONE [Mon.TELEPHONE] – with this option enabled, the control panel

can send event codes by means of the telephone line (in the case of INTEGRA 128-WRL

control panel – the GSM voice channel).

Reporting - GPRS [Mon.GPRS] – if the option is enabled:

– the INTEGRA 128-WRL control panel can send event codes via GPRS,

– any control panel can send event codes via GPRS by using the SATEL GSM module.

The REPORTING – GPRS option does not apply to GPRS reporting via the INT-GSM

module.

Reporting - ETHM [Mon.ETHM-1] – the option is available if the ETHM-1 Plus / ETHM-1

module is connected to the control panel, but the INT-GSM module is not included in the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info