Bedienungsanleitung Satel Integra 128 (Seite 107 von 114) (Englisch)

699073

107

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 105

2. Using the telephone options (see: “Telephone options” p. 69):

– define the mode of dialing the telephone numbers (TONE DIALING option and – in case of

the pulse dialing – PULSE DIALING 1/1.5 (OFF 1/2) option),

– determine whether the control panel, prior to dialing the number, should check the

telephone line for dialing signal (NO DIAL TONE TEST option),

– determine whether the control panel is to play back the voice message after going off-

hook, or 15 seconds after the dialing is completed (global option NO ANSWER TEST).

– determine whether the voice message is to be played back once or twice (option

DOUBLE VOICE MESSAGE).

3. Define the number of attempts to get connected in one round (function MAX. REDIAL

NUMBER FOR ONE ROUND

4. Define parameters of the telephones to which messages are to be sent:

– name (up to 16 characters),

– telephone number,

– type of messaging (select 0 – voice),

– number of attempts made by the control panel to notify the indicated telephone

number about the event, if receipt of the message has not been acknowledged,

– how the receipt of voice message is to be acknowledged (if the messaging is to be

acknowledged, enable the ANY CODE option or enter the 4-digit code).

5. Record or synthesize the voice messages which are to be used for messaging (see:

CA-64 SM synthesizer or INT-VG voice module manual).

6. For events about which the control panel is to inform, indicate:

– number of the voice message to be used for messaging,

– telephones to be notified.

7. In order to limit unnecessary messaging, define the cases in which notification can be

cancelled (the parameters CLEARING IN PARTITIONS and CLEARING AFTER ACKNOWLEDGEMENT

and the option CLEAR MESSAGING ON ALARM CLEARING).

14. Answering phone calls and remote control

The call answering function allows the control panel users to receive information on

the partition status (arm mode, alarms). Owing to the telephone control function, the users

can control the REMOTE SWITCH outputs by means of a telephone.

The INT-VG module offers a much larger scope of the alarm system remote operation

functionality using a telephone.

The parameters of telephone answering and control can be programmed:

• using the keypad, in the service mode, by means of the functions available in the

TEL.ANSW./CTRL. submenu,

• using the DLOADX program, in the “Answering and remote control” window.

14.1 Telephone answering and control parameters and options

See also section “Telephone options” p. 69.

Shown in square brackets are the names used in keypads.

Answer if all chosen partitions are armed [On armed part.] – you can indicate the

partitions whose status will affect the telephone answering and control functions (they will

only be executed, if all indicated partitions are armed).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Seite 107

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info