Bedienungsanleitung Satel Integra 24 (Seite 52 von 114) (Englisch)

699079

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

50 Programming SATEL

Audible alarm after verification [Bell on 2nd] – if this option is enabled, the alarms from

zones with the PRE-ALARM or WITH VERIFICATION option enabled will only trigger loud alarm

signaling after verification. The unverified alarms will not trigger loud alarm signaling.

Partition timer

Partitions can be controlled with an additional timer, which can be programmed:

• in the keypad, using the function available in the user menu ([code] OPTIONS

PROGRAMMING

PARTITION TIMERS),

• in the DLOADX program connected to the control panel, in the “Structure” window,

“System” tab, after clicking on the partition name and then on the “Partition timer” button.

4.3 Zones

The zone is a separated portion of the protected area which can be supervised by a detector

or detectors. A zone can only be assigned to one partition.

The system supports the following zones:

• hardwired – on the control panel electronics board, in keypads and expanders.

The number of available hardwired zones is determined by the control panel during

identification procedure.

• wireless – in the INTEGRA 128-WRL control panel or after connecting the ABAX 2 /

ABAX wireless system controller. The number of available wireless zones depends on the

number of wireless devices registered in the system and is determined during the

procedure of adding the devices.

• virtual – zones which physically do not exist, but have been programmed as FOLLOW

OUTPUT

or are controlled by means of a keyfob.

4.3.1 Assigning zones to a partition

The zones can be assigned to a partition:

• using the keypad, in the service mode, by means of the ZONES function (STRUCTURE

SYSTEM PARTITIONS SETTINGS [Part. Name] ZONES) – see: “Selection from the

multiple-choice list” p. 26,

• using the DLOADX program:

1. in the “Structure” window, “System” tab, after clicking on the partition name. Click on

the “Add” button to display the list of zones which can be assigned to the selected

partition. Click on the zone which is to be assigned to the partition.

2. in the “Zones” window, “Zones” tab, “Part.” column, enter the number of partition to

which the given zone is to be assigned.

4.3.2 Programming the EOL resistor values

For the zones on INTEGRA 128-WRL control panel mainboard, some keypads and

expanders, the value of end-of-line resistors is programmable within the range from 500 Ω to

15 kΩ (the sum of preset values may not exceed 15 kΩ).

The value of EOL resistors for the zones on the INTEGRA 128-WRL control panel mainboard

can be programmed:

• using the keypad, in the service mode, by means of EOL R1 RESISTOR and EOL R2

RESISTOR

functions (STRUCTURE HARDWARE EOL R1 RESISTOR / EOL R2 RESISTOR),

• using the DLOADX program, in the “Structure” window, “Hardware” tab, after clicking on

the control panel mainboard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 24 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info