Bedienungsanleitung Satel Integra 24 (Seite 73 von 114) (Englisch)

699079

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 71

Double call – with this option enabled, the control panel must be called twice for the modem

communication to be established. The first time you must wait for the preprogrammed

number of rings and hang up. Then you must call back within three minutes and the

control panel will answer the call immediately. This solution makes it possible to connect

after the control panel some additional devices which will be activated after a preset

number of rings (e.g. answering machine, fax, etc.).

Pulse dialing 1/1.5 (off 1/2) – this option applies to dialing the telephone numbers by using

the pulse mode. Before you enable it, make yourself familiar with the valid standard of

pulse dialing.

Rings before answer [Rings to answer] – number of rings after which the control panel will

go off hook.

6.2 Printer options

Printing – the option enables on-line events printout by the printer connected to the RS-232

port of control panel mainboard.

6.2.1 Printout options

Include reporting status [Monitor.status] – on the printout will appear the information if the

particular event was sent to the monitoring station (printout of the event information will

take place not immediately but after transmission to the station has been completed).

Print names / descriptions [Names/descript] – determines if, besides the numbers of zones,

outputs, modules and users, also their names and descriptions are to be printed.

Wide paper – printout width will be 132 columns (if the option is disabled: 80 columns).

2400 bps (off:1200 bps) – data will be sent to RS-232 port at a rate of 2400 bps (if the

option is disabled - at a rate of 1200 bps).

CR+LF (off: CR) – parameter determining the control mode of paper feed in the printer.

Use parity bit – the parity check of data transferred from the control panel to the printer is

enabled.

Parity EVEN (off: ODD) – option determines the mode of parity check of data transferred

from the control panel to the printer. The option is relevant only if the USE PARITY BIT option

is active.

The other parameters of RS-232 transmission are permanently programmed (8 data

bits, 1 stop bit).

All the parameters regarding transmission through RS-232 (i.e. transmission rate,

CR+LF, parity, data bits and stop bits) are to be set identically on the control panel and

on the connected printer. Otherwise the printer will not operate at all, or the printout

will be illegible.

6.2.2 Printout contents

The options define what kind of information will be contained in the printout.

6.3 Other options

Permitted “simple” access codes [Simple codes] – with this option enabled, with this

option enabled, it is possible to use codes containing less than three different digits (e.g.

1111 or 1212) or consisting of consecutive digits (e.g. 3456).

Notify of necessity to change access code [Notify of code] – with this option enabled, the

keypad will notify the user of the necessity to change access code, if it is known to other

users.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 24 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info